 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| P89CV51RB2/RC2/RD2 8-bit 80C51 5 V low power 64 kB flash microcontroller with 1 kB RAM, SPI, 6-clock CPU with 6/12-clock peripherals Rev. 01 -- 5 October 2007 Product data sheet 1. General description The P89CV51RB2/RC2/RD2 are three types of 80C51 microcontroller with respectively 16 kB/32 kB/64 kB flash and 1 kB of data RAM. These devices are designed to be drop-in and software-compatible replacements for the popular P89C51RB2/RC2/RD2 devices. Both the In-System Programming (ISP) and In-Application Programming (IAP) boot codes are upward compatible. Additional features of the P89CV51RB2/RC2/RD2 devices compared to the P89C51RB2/RC2/RD2 are the inclusion of an SPI interface, larger RAM size, and the ability to erase code memory in 128-B page blocks. The IAP capability combined with the 128-B page size allows for efficient use of the code memory for non-volatile data storage. 2. Features 2.1 Principal features I Supports 12-clock (default) or 6-clock mode selection via ISP or parallel programmer I 6-clock/12-clock mode programmable "on-the-fly" by an SFR bit I Peripherals (PCA, timers, UART) may use either 6-clock or 12-clock mode while the CPU is in 6-clock mode I 128-B page erase for efficient use of code memory as non-volatile data storage I 0 MHz to 40 MHz operating frequency in 12x mode, 20 MHz in 6x mode I 16/32/64 kB of on-chip flash user-code memory with ISP and IAP I 1 kB RAM I SPI (Serial Peripheral Interface) and enhanced UART I PCA (Programmable Counter Array) with PWM and capture/compare functions I Three 16-bit timers/counters 2.2 Additional features I I I I I I I Four 8-bit I/O ports WatchDog Timer (WDT) 30 ms page erase, 150 ms block erase PLCC44 and TQFP44 packages Ten interrupt sources with four priority levels Second DPTR register Low EMI mode (ALE inhibit) NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI I Power-down mode with external interrupt wake-up I Idle mode 2.3 Comparison to P89C51RB2/RC2/RD2 devices I SPI: The P89CV51RB2/RC2/RD2 devices have an SPI interface that was not present on the P89C51RB2/RC2/RD2 devices. I Smaller block size: The page size decreased from 4 kB to 128 B. These smaller pages can be erased and reprogrammed using IAP function calls, which makes practical use of code memory for non-volatile data storage. A page is erased in 30 ms or less. IAP and ISP code both support 128-B page operations. The IAP and ISP code uses multiple page-erase operations to emulate the erasing of larger block sizes (8 kB and 16 kB) to maintain firmware compatibility. I Status bit replaces Status byte: Automatic entry into ISP mode following a reset is now controlled by one status bit. Its operation is almost identical to that used by the previous devices, which was based on the zero/non-zero value of the status byte. I Faster block erase: The erase time for the entire user-code memory of the P89CV51RB2/RC2/RD2 devices is 150 ms, which is a significant improvement. I Larger RAM size: RAM size increased from 512 B to 1 kB. 3. Ordering information Table 1. Ordering information Package Name P89CV51RB2FA P89CV51RB2FBC P89CV51RC2FA P89CV51RC2FBC P89CV51RD2FA P89CV51RD2FBC PLCC44 TQFP44 PLCC44 TQFP44 PLCC44 TQFP44 Description plastic leaded chip carrier; 44 leads plastic thin quad flat package; 44 leads; body 10 x 10 x 1.0 mm plastic leaded chip carrier; 44 leads plastic thin quad flat package; 44 leads; body 10 x 10 x 1.0 mm plastic leaded chip carrier; 44 leads plastic thin quad flat package; 44 leads; body 10 x 10 x 1.0 mm Version SOT187-2 SOT376-1 SOT187-2 SOT376-1 SOT187-2 SOT376-1 Type number 3.1 Ordering options Table 2. Ordering options Flash memory 16 kB 32 kB 64 kB RAM 1 kB 1 kB 1 kB Temperature range -40 C to +85 C Frequency 0 MHz to 40 MHz Type number P89CV51RB2FA P89CV51RB2FBC P89CV51RC2FA P89CV51RC2FBC P89CV51RD2FA P89CV51RD2FBC P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 2 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 4. Block diagram P89CV51RB2/RC2/RD2 HIGH PERFORMANCE 80C51 CPU 16 kB/32 kB/64 kB CODE FLASH 1 kB DATA RAM UART internal bus SPI TXD RXD SPICLK MOSI MISO SS T0 T1 T2 T2EX P3[7:0] PORT 3 TIMER 0 TIMER 1 P2[7:0] PORT 2 TIMER 2 P1[7:0] PORT 1 PCA PROGRAMMABLE COUNTER ARRAY CEX[4:0] P0[7:0] PORT 0 WATCHDOG TIMER CRYSTAL OR RESONATOR XTAL1 OSCILLATOR XTAL2 002aac960 Fig 1. Block diagram P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 3 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 5. Pinning information 5.1 Pinning P1[4]/CEX1/SS P1[3]/CEX0 P1[1]/T2EX 43 P0[0]/AD0 42 P0[1]/AD1 41 P0[2]/AD2 P1[5]/CEX2/MOSI P1[6]/CEX3/MISO P1[7]/CEX4/SPICLK 7 8 9 40 P0[3]/AD3 39 P0[4]/AD4 38 P0[5]/AD5 37 P0[6]/AD6 36 P0[7]/AD7 35 EA 34 n.c. 33 ALE 32 PSEN 31 P2[7]/A15 30 P2[6]/A14 29 P2[5]/A13 P2[4]/A12 28 002aac962 P1[2]/ECI P1[0]/T2 2 VSS 22 RST 10 P3[0]/RXD 11 n.c. 12 P3[1]/TXD 13 P3[2]/INT0 14 P3[3]/INT1 15 P3[4]/T0 16 P3[5]/T1 17 P3[6]/WR 18 P3[7]/RD 19 XTAL2 20 XTAL1 21 n.c. 23 P2[0]/A8 24 P2[1]/A9 25 P2[2]/A10 26 P2[3]/A11 27 P89CV51RB2/RC2/RD2 Fig 2. PLCC44 pin configuration P89CV51RB2_RC2_RD2_1 44 VDD 6 5 4 3 1 n.c. (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 4 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 44 P1[4]/CEX1/SS 43 P1[3]/CEX0 41 P1[1]/T2EX 37 P0[0]/AD0 36 P0[1]/AD1 35 P0[2]/AD2 P1[5]/CEX2/MOSI P1[6]/CEX3/MISO P1[7]/CEX4/SPICLK RST P3[0]/RXD n.c. P3[1]/TXD P3[2]/INT0 P3[3]/INT1 1 2 3 4 5 6 7 8 9 34 P0[3]/AD3 33 P0[4]/AD4 32 P0[5]/AD5 31 P0[6]/AD6 30 P0[7]/AD7 29 EA 28 n.c. 27 ALE 26 PSEN 25 P2[7]/A15 24 P2[6]/A14 23 P2[5]/A13 P2[4]/A12 22 002aac961 42 P1[2]/ECI 40 P1[0]/T2 VSS 16 P89CV51RB2/RC2/RD2 P3[4]/T0 10 P3[5]/T1 11 P3[6]/WR 12 P3[7]/RD 13 XTAL2 14 XTAL1 15 n.c. 17 P2[0]/A8 18 P2[1]/A9 19 P2[2]/A10 20 P2[3]/A11 21 Fig 3. TQFP44 pin configuration 5.2 Pin description Table 3. Symbol P0[0] to P0[7] P89CV51RB2/RC2/RD2 Pin description Pin PLCC44 TQFP44 I/O Port 0: Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float, and in this state can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external code and data memory. In this application, it uses strong internal pull-ups when transitioning to 1s. External pull-ups are required when used as a general purpose I/O port. P0[0] -- Port 0 bit 0. AD0 -- Address/data bit 0. P0[1] -- Port 0 bit 1. AD1 -- Address/data bit 1. P0[2] -- Port 0 bit 2. AD2 -- Address/data bit 2. P0[3] -- Port 0 bit 3. AD3 -- Address/data bit 3. P0[4] -- Port 0 bit 4. AD4 -- Address/data bit 4. P0[5] -- Port 0 bit 5. AD5 -- Address/data bit 5. (c) NXP B.V. 2007. All rights reserved. Type Description P0[0]/AD0 P0[1]/AD1 P0[2]/AD2 P0[3]/AD3 P0[4]/AD4 P0[5]/AD5 43 42 41 40 39 38 37 36 35 34 33 32 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O P89CV51RB2_RC2_RD2_1 Product data sheet Rev. 01 -- 5 October 2007 38 VDD 39 n.c. 5 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 3. Symbol P0[6]/AD6 P0[7]/AD7 P89CV51RB2/RC2/RD2 Pin description ...continued Pin PLCC44 37 36 TQFP44 31 30 I/O I/O I/O I/O I/O with internal pull-up P0[6] -- Port 0 bit 6. AD6 -- Address/data bit 6. P0[7] -- Port 0 bit 7. AD7 -- Address/data bit 7. Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 1 pins are pulled HIGH by the internal pull-ups when 1s are written to them and can be used as inputs in this state. As inputs, Port 1 pins that are externally pulled LOW will source current (IIL) because of the internal pull-ups. P1[5], P1[6], P1[7] have high current drive of 16 mA. P1[0] -- Port 1 bit 0. T2 -- External count input to timer/counter 2 or clock-out from timer/counter 2. P1[1] -- Port 1 bit 1. T2EX: Timer/counter 2 capture/reload trigger and direction control. P1[2] -- Port 1 bit 2. ECI -- External clock input. This signal is the external clock input for the PCA. P1[3] -- Port 1 bit 3. CEX0 -- Capture/compare external I/O for PCA Module 0. Each capture/compare module connects to a Port 1 pin for external I/O. When not used by the PCA, this pin can handle standard I/O. P1[4] -- Port 1 bit 4. CEX1 -- Capture/compare external I/O for PCA Module 1. SS -- Slave Select input for SPI. P1[5] -- Port 1 bit 5. CEX2 -- Capture/compare external I/O for PCA Module 2. MOSI -- Master output/slave input for SPI. P1[6] -- Port 1 bit 6. CEX3 -- Capture/compare external I/O for PCA Module 3. MISO -- Master input/slave output for SPI. P1[7] -- Port 1 bit 7. CEX4 -- Capture/compare external I/O for PCA Module 4. SPICLK -- Serial clock input/output for SPI. Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins are pulled HIGH by the internal pull-ups when 1s are written to them and can be used as inputs in this state. As inputs, Port 2 pins that are externally pulled LOW will source current (IIL) because of the internal pull-ups. Port 2 sends the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit address (MOVX @DPTR). In this application, it uses strong internal pull-ups when transitioning to 1s. P2[0] -- Port 2 bit 0. A8 -- Address bit 8. Type Description P1[0] to P1[7] P1[0]/T2 2 40 I/O I/O P1[1]/T2EX P1[2]/ECI 3 4 41 42 I/O I I/O I P1[3]/CEX0 5 43 I/O I/O P1[4]/CEX1/ SS 6 44 I/O I/O I P1[5]/CEX2/ MOSI 7 1 I/O I/O I/O P1[6]/CEX3/ MISO 8 2 I/O I/O I/O P1[7]/CEX4/ SPICLK 9 3 I/O I/O I/O I/O with internal pull-up P2[0] to P2[7] P2[0]/A8 24 18 I/O O P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 6 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 3. Symbol P2[1]/A9 P2[2]/A10 P2[3]/A11 P2[4]/A12 P2[5]/A13 P2[6]/A14 P2[7]/A15 P89CV51RB2/RC2/RD2 Pin description ...continued Pin PLCC44 25 26 27 28 29 30 31 TQFP44 19 20 21 22 23 24 25 I/O O I/O O I/O O I/O O I/O O I/O O I/O O I/O with internal pull-up P2[1] -- Port 2 bit 1. A9 -- Address bit 9. P2[2] -- Port 2 bit 2. A10 -- Address bit 10. P2[3] -- Port 2 bit 3. A11 -- Address bit 11. P2[4] -- Port 2 bit 4. A12 -- Address bit 12. P2[5] -- Port 2 bit 5. A13 -- Address bit 13. P2[6] -- Port 2 bit 6. A14 -- Address bit 14. P2[7] -- Port 2 bit 7. A15 -- Address bit 15. Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins are pulled HIGH by the internal pull-ups when 1s are written to them and can be used as inputs in this state. As inputs, Port 3 pins that are externally pulled LOW will source current (IIL) because of the internal pull-ups. P3[0] -- Port 3 bit 0. RXD -- Serial input port. P3[1] -- Port 3 bit 1. TXD -- Serial output port. P3[2] -- Port 3 bit 2. INT0 -- External interrupt 0 input. P3[3] -- Port 3 bit 3. INT1 -- External interrupt 1 input. P3[4] -- Port 3 bit 4. T0 -- External count input to timer/counter 0. P3[5] -- Port 3 bit 5. T1 -- External count input to timer/counter 1. P3[6] -- Port 3 bit 6. WR -- External data memory write strobe. P3[7] -- Port 3 bit 7. RD -- External data memory read strobe. Program Store Enable: PSEN is the read strobe for external program memory. When the device is executing from internal program memory, PSEN is inactive (HIGH). When the device is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. Type Description P3[0] to P3[7] P3[0]/RXD P3[1]/TXD P3[2]/INT0 P3[3]/INT1 P3[4]/T0 P3[5]/T1 P3[6]/WR P3[7]/RD PSEN 11 13 14 15 16 17 18 19 32 5 7 8 9 10 11 12 13 26 I/O I I/O O I/O I I/O I I/O I I/O I I/O O I/O O O P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 7 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 3. Symbol RST EA P89CV51RB2/RC2/RD2 Pin description ...continued Pin PLCC44 10 35 TQFP44 4 29 I I Reset: While the oscillator is running, a HIGH logic state on this pin for two machine cycles will reset the device. External Access Enable: EA must be connected to VSS in order to enable the device to fetch code from the external program memory. EA must be strapped to VDD for internal program execution. Address Latch Enable: ALE is the output signal for latching the low byte of the address during an access to external memory. Normally the ALE[1] is emitted at a constant rate of 16 the crystal frequency[2] and can be used for external timing and clocking. One ALE pulse is skipped during each access to external data memory. However, if bit AO is set to 1, ALE is disabled. Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. Crystal 2: Output from the inverting oscillator amplifier. Power supply Ground Type Description ALE 33 27 I/O XTAL1 XTAL2 VDD VSS [1] [2] 21 20 44 22 15 14 38 16 I O supply supply ALE loading issue: When ALE pin experiences higher loading (> 30 pF) during the reset, the microcontroller may accidentally enter into modes other than normal working mode. The solution is to add a pull-up resistor from 3 k to 50 k between e.g., ALE pin and VDD. For 6-clock mode, ALE is emitted at 13 of crystal frequency. 6. Functional description 6.1 Special function registers Remark: SFR accesses are restricted in the following ways: * Do not attempt to access any SFR locations that are undefined. * Access to defined SFR locations must be strictly for the functions of the SFRs. * SFR bits labeled `-', `0' or `1' can only be written and read as follows: - `-' Unless otherwise specified, must be written with `0', but can return any value when read (even if it was written with `0'). It is a reserved bit and may be used in future derivatives. - `0' must be written with `0', and will return a `0' when read. - `1' must be written with `1', and will return a `1' when read. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 8 of 73 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data sheet Rev. 01 -- 5 October 2007 (c) NXP B.V. 2007. All rights reserved. P89CV51RB2_RC2_RD2_1 NXP Semiconductors Table 4. Special function registers * indicates SFRs that are bit addressable. Name Description SFR address Bit address ACC* AUXR AUXR1 B* CCAP0H CCAP1H CCAP2H CCAP3H CCAP4H CCAP0L CCAP1L CCAP2L CCAP3L CCAP4L CCAPM0 CCAPM1 CCAPM2 CCAPM3 CCAPM4 CCON* CH CL CMOD CKCON Accumulator Auxiliary function Register Auxiliary function Register 1 B register Module 0 Capture High Module 1 Capture High Module 2 Capture High Module 3 Capture High Module 4 Capture High Module 0 Capture Low Module 1 Capture Low Module 2 Capture Low Module 3 Capture Low Module 4 Capture Low Module 0 mode Module 1 mode Module 2 mode Module 3 mode Module 4 mode PCA Counter Control PCA Counter High PCA Counter Low PCA Counter Mode Clock Control E0H 8EH A2H Bit address F0H FAH FBH FCH FDH FEH EAH EBH ECH EDH EEH DAH DBH DCH DDH DEH Bit address D8H F9H E9H C1H 8FH Bit functions and addresses[1] MSB E7 F7 DF CF CIDL SPIX2 E6 F6 ECOM_0 ECOM_1 ECOM_2 ECOM_3 ECOM_4 DE CR WDTE WDX2 E5 F5 CAPP_0 CAPP_1 CAPP_2 CAPP_3 CAPP_4 DD PCAX2 E4 F4 CAPN_0 CAPN_1 CAPN_2 CAPN_3 CAPN_4 DC CCF4 SIX2 E3 GF2 F3 MAT_0 MAT_1 MAT_2 MAT_3 MAT_4 DB CCF3 T2X2 E2 0 F2 TOG_0 TOG_1 TOG_2 TOG_3 TOG_4 DA CCF2 CPS1 T1X2 E1 EXTRAM F1 PWM_0 PWM_1 PWM_2 PWM_3 PWM_4 D9 CCF1 CPS0 T0X2 LSB E0 AO DPS F0 - P89CV51RB2/RC2/RD2 ECCF_0 ECCF_1 ECCF_2 ECCF_3 ECCF_4 80C51 with 1 kB RAM, SPI D8 CCF0 ECF X2 9 of 73 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 4. Special function registers ...continued * indicates SFRs that are bit addressable. Name DPTR DPH DPL IE* IP* IPH P0* Rev. 01 -- 5 October 2007 (c) NXP B.V. 2007. All rights reserved. Product data sheet 10 of 73 P89CV51RB2_RC2_RD2_1 NXP Semiconductors Description Data Pointer (2 B) Data Pointer High Data Pointer Low Interrupt Enable Interrupt Priority Low Interrupt Priority High Port 0 Port 1 SFR address Bit functions and addresses[1] MSB AF EA BF 87 AD7 97 CEX4/ SPICLK A7 A15 B7 RD SMOD1 D7 CY 9F SM0/FE AE EC BE PPC PPCH 86 AD6 96 CEX3/ MISO A6 A14 B6 WR SMOD0 D6 AC 9E SM1 AD ET2 BD PT2 PT2H 85 AD5 95 CEX2/ MOSI A5 A13 B5 T1 D5 F0 9D SM2 AC ES BC PS PSH 84 AD4 94 CEX1/SS A4 A12 B4 T0 POF D4 RS1 9C REN AB ET1 BB PT1 PT1H 83 AD3 93 CEX0 A3 A11 B3 INT1 GF1 D3 RS0 9B TB8 AA EX1 BA PX1 PX1H 82 AD2 92 ECI A2 A10 B2 INT0 GF0 D2 OV 9A RB8 A9 ET0 B9 PT0 PT0H 81 AD1 91 T2EX A1 A9 B1 TXD PD D1 F1 99 TI LSB A8 EX0 B8 PX0 PX0H 80 AD0 90 T2 A0 A8 B0 RXD IDL D0 P 98 RI - 83H 82H Bit address A8H Bit address B8H B7H Bit address 80H Bit address 90H Bit address P1* P2* P3* PCON PSW* RCAP2H RCAP2L SCON* SBUF SADDR SADEN Port 2 Port 3 Power Control Program Status Word Timer 2 Capture High Timer 2 Capture Low Serial port Control Serial port data Buffer Serial port Address Serial port Address Enable A0H Bit address B0H 87H Bit address D0H CBH CAH Bit address 98H 99H A9H B9H P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 4. Special function registers ...continued * indicates SFRs that are bit addressable. Name Description SFR address Bit address SPCR SPSR SPDAT SP TCON* T2CON* T2MOD Rev. 01 -- 5 October 2007 (c) NXP B.V. 2007. All rights reserved. Product data sheet 11 of 73 P89CV51RB2_RC2_RD2_1 NXP Semiconductors Bit functions and addresses[1] MSB 87 SPIE SPIF 8F TF1 CF TF2 T1GATE 86 SPEN WCOL 8E TR1 CE EXF2 T1C/T 85 DORD 8D TF0 CD RCLK T1M1 84 MSTR 8C TR0 CC TCLK T1M0 83 CPOL 8B IE1 CB EXEN2 T0GATE 82 CPHA 8A IT1 CA TR2 T0C/T 81 SPR1 89 IE0 C9 C/T2 T2OE T0M1 LSB 80 SPR0 88 IT0 C8 CP/RL2 DCEN - SPI Control Register SPI Status Register SPI Data Stack Pointer Timer/counter Control Timer/counter 2 Control Timer 2 Mode control Timer 0 High Timer 1 High Timer 2 High Timer 0 Low Timer 1 Low Timer 2 Low Timer/counter 0 and 1 Mode WatchDog Timer Reset D5H AAH 86H 81H Bit address 88H Bit address C8H C9H 8CH 8DH CDH 8AH 8BH CCH 89H A6H TH0 TH1 TH2 TL0 TL1 TL2 TMOD WDTRST [1] P89CV51RB2/RC2/RD2 T0M0 - Unimplemented bits in SFRs (labeled `-') are `X' (unknown) at all times. Unless otherwise specified, 1s should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are 0s although they are unknown when read. 80C51 with 1 kB RAM, SPI NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.2 Memory organization The various P89CV51RB2/RC2/RD2 memory spaces are as follows: * DATA 128 B of internal data memory space (00H:7FH) accessed via direct or indirect addressing, using instructions other than MOVX and MOVC. All or part of the stack may be in this area. * IDATA Indirect Data. 256 B of internal data memory space (00H:FFH) accessed via indirect addressing using instructions other than MOVX and MOVC. All or part of the stack may be in this area. This area includes the DATA area and the 128 B immediately above it. * SFR Special Function Registers. Selected CPU registers and peripheral control and status registers, accessible only via direct addressing. * XDATA `External' Data or auxiliary RAM. Duplicates the classic 80C51 64 kB memory space addressed via the MOVX instruction using the DPTR, R0, or R1. The P89CV51RB2/RC2/RD2 have 768 B of on-chip XDATA memory. * CODE 64 kB of code memory space, accessed as part of program execution and via the MOVC instruction. The P89CV51RB2/RC2/RD2 have 16/32/64 kB of on-chip code memory. 6.2.1 Expanded data RAM addressing The P89CV51RB2/RC2/RD2 have 1 kB of data RAM; see Figure 4. To access the expanded RAM (XRAM), the EXTRAM bit must be set and MOVX instructions must be used. The extra memory is physically located on the chip and logically occupies the first bytes of external memory (addresses 000H to 2FFH). Table 5. AUXR - Auxiliary function register (address 8EH) bit allocation Not bit addressable; reset value 00H. Bit Symbol 7 6 5 4 3 2 1 EXTRAM 0 AO When EXTRAM = 1, the expanded RAM is indirectly addressed using the MOVX instruction in combination with any of the registers R0, R1 of the selected bank or DPTR. Accessing the expanded RAM does not affect ports P0, P3[6] (WR), P3[7] (RD), or P2. With EXTRAM = 1, the expanded RAM can be accessed as in the following example. Expanded RAM access (indirect addressing only): MOVX @DPTR, A; DPTR contains 0A0H P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 12 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI The DPTR points to location 0A0H and the data in the accumulator is written to address 0A0H of the expanded RAM rather than off-chip external memory. Access to EXTRAM addresses that are not present on the device (above 2FFH) will access external off-chip memory and will perform in the same way as the standard 8051, with P0 and P2 as data/address bus, and P3[6] and P3[7] as write and read timing signals. Table 6. Bit 7 to 2 1 AUXR - Auxiliary function register (address 8EH) bit description Symbol EXTRAM Description Reserved for future use. Should be set to 0 by user programs. Internal/external RAM access using MOVX @Ri/@DPTR. When 1, accesses internal XRAM with address specified in MOVX instruction. If address supplied with this instruction exceeds on-chip available XRAM, off-chip RAM is accessed. When 0, every MOVX instruction targets external data memory by default. ALE off: disables/enables ALE. AO = 0 results in ALE emitted at a constant rate of 12 the oscillator frequency. In case of AO = 1, ALE is active only during a MOVX or MOVC. 0 AO When EXTRAM = 0, MOVX @Ri and MOVX @DPTR will be similar to the standard 8051. Using MOVX @Ri provides an 8-bit address with multiplexed data on Port 0. Other output port pins can be used to output higher order address bits. This provides external paging capabilities. Using MOVX @DPTR generates a 16-bit address. This allows external addressing up to 64 kB. Port 2 provides the high-order eight address bits (DPH), and Port 0 multiplexes the low-order eight address bits (DPL) with data. Both MOVX @Ri and MOVX @DPTR generates the necessary read and write signals (P3[6] - WR and P3[7] RD) for external memory use. Table 7 shows external data memory RD, WR operation with EXTRAM bit. The stack pointer (SP) can be located anywhere within the 256 B of internal RAM (lower 128 B and upper 128 B). The stack pointer may not be located in any part of the expanded RAM. Table 7. AUXR EXTRAM = 0 EXTRAM = 1 External data memory RD, WR with EXTRAM bit MOVX @DPTR, A or MOVX A, @DPTR ADDR < 0300H RD/WR asserted RD/WR not asserted ADDR 0300H RD/WR asserted RD/WR asserted MOVX @Ri, A or MOVX A, @Ri ADDR = any RD/WR asserted RD/WR not asserted P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 13 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 2FFH EXPANDED RAM 768 B FFH (INDIRECT ADDRESSING) FFH (DIRECT ADDRESSING) SPECIAL FUNCTION REGISTERS (SFRs) 80H 7FH UPPER 128 B INTERNAL RAM LOWER 128 B INTERNAL RAM (INDIRECT AND DIRECT ADDRESSING) 80H 000H (INDIRECT ADDRESSING) 00H FFFFH (INDIRECT ADDRESSING) EXTERNAL DATA MEMORY FFFFH (INDIRECT ADDRESSING) EXTERNAL DATA MEMORY 0300H 2FFH EXPANDED RAM 000H EXTRAM = 0 0000H EXTRAM = 1 002aaa517 Fig 4. Internal and external data memory structure 6.2.2 Dual data pointers The device has two 16-bit data pointers. The DPTR Select (DPS) bit in AUXR1 determines which of the two data pointers is accessed. When DPS = 0, DPTR0 is selected; when DPS = 1, DPTR1 is selected. Quickly switching between the two data pointers can be accomplished by a single INC instruction on AUXR1; see Figure 5. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 14 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI AUXR1 / bit0 DPS DPTR1 DPS = 0 DPTR0 DPS = 1 DPTR1 DPTR0 DPH 83H DPL 82H external data memory 002aaa518 Fig 5. Dual data pointer organization Table 8. AUXR1 - Auxiliary function register 1 (address A2H) bit allocation Not bit addressable; reset value 00H. Bit Symbol Table 9. Bit 7 to 4 3 2 1 0 7 6 5 4 3 GF2 2 0 1 0 DPS AUXR1 - Auxiliary function register 1 (address A2H) bit description Symbol GF2 0 DPS Description Reserved for future use. Should be set to 0 by user programs. General purpose user-defined Flag. This bit contains a hard-wired 0. Allows toggling of the DPS bit by incrementing AUXR1, without interfering with other bits in the register. Reserved for future use. Should be set to 0 by user programs. Data Pointer Select. Chooses one of two data pointers for use by the program. See text for details. 6.2.3 Reset At initial power-up, the port pins will be in a random state until the oscillator has started and the internal reset algorithm has weakly pulled all pins HIGH. Powering up the device without a valid reset could cause the MCU to start executing instructions from an indeterminate location. Such undefined states may inadvertently corrupt the code in the flash. A system reset will not affect the on-chip RAM while the device is running, however, the contents of the on-chip RAM during power-up are indeterminate. When power is applied to the device, the RST pin must be held HIGH long enough for the oscillator to start-up (usually several milliseconds for a low frequency crystal), in addition to two machine cycles for a valid power-on reset. An example of a method to extend the RST signal is to implement an RC circuit by connecting the RST pin to VDD through a 10 F capacitor and to VSS through an 8.2 k resistor as shown in Figure 6. During initial power-up the POF flag in the PCON register is set to indicate an initial power-up condition. The POF flag will remain active until cleared by software. Following a reset condition, under normal conditions, the MCU will start executing code from address 0000H in the user's code memory. However if either the PSEN pin was LOW when reset was exited, or the status bit = 1, the MCU will start executing code from the boot address. The boot address is formed using the value of the boot vector as the high byte of the address and 00H as the low byte. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 15 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI VDD 10 F VDD RST 8.2 k C2 XTAL2 XTAL1 C1 002aaa543 Fig 6. Power-on reset circuit 6.3 Flash memory 6.3.1 Flash organization The P89CV51RB2/RC2/RD2 program memory consists of a 16/32/64 kB block for user code. The flash can be read or written in bytes and can be erased in 128-B pages. A chip erase function will erase the entire user code memory and its associated security bits. There are three methods for erasing or programming the flash memory that may be used. First, the flash may be programmed or erased in the end-user application by calling LOW-state routines through a common IAP entry point. Second, the on-chip ISP bootloader may be invoked. This ISP bootloader will, in turn, call LOW-state routines through the same common entry point that can be used by the end-user application. Third, the flash may be programmed or erased using the parallel method by using a commercially available EPROM programmer which supports this device. 6.3.2 Features * Flash internal program memory with 128-B page erase. * Internal boot block, containing LOW-state IAP routines available to user code. * Boot vector allows user-provided flash loader code to reside anywhere in the flash memory space, providing flexibility to the user. * Default loader providing ISP via the serial port, located in upper-end of program memory. * * * * * Programming and erase over the full operating voltage range. Read/Programming/Erase using ISP/IAP. Programming with industry-standard commercial programmers. 10000 typical erase/program cycles for each byte. 100 year minimum data retention. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 16 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.3.3 Boot block When the microcontroller programs its own flash memory, all of the low-level details are handled by code (bootloader) that is contained in a boot block. A user program calls the common entry point in the boot block with appropriate parameters to accomplish the desired operation. Boot block operations include erase user code, program user code, program security bits, chip erase, etc. The boot block logically overlays the program memory space from FC00H to FFFFH, when it is enabled. The boot block may be disabled on-the-fly so that the upper 1 kB of user code is available to the user's program. 6.3.4 Power-on reset code execution The P89CV51RB2/RC2/RD2 contains two special flash elements: the boot vector and the boot status bit. Following reset, the P89CV51RB2/RC2/RD2 examines the contents of the boot status bit. If the boot status bit is set to zero, power-up execution starts at location 0000H, which is the normal start address of the user's application code. When the boot status bit is set to a value other than zero, the contents of the boot vector are used as the high byte of the execution address and the low byte is set to 00H. Table 10 shows the factory default boot vector setting for this device. A factory-provided bootloader is pre-programmed into the address space indicated and uses the indicated bootloader entry point to perform ISP functions. Table 10. Device P89CV51RB2/RC2/RD2 Default boot vector values and ISP entry points Default boot vector FCH Default bootloader entry point FC00H Default bootloader code range FC00H to FFFFH 6.3.5 Hardware activation of the bootloader The bootloader can also be executed by forcing the device into ISP mode during a power-on sequence. This has the same effect as having a non-zero status byte. This allows an application to be built that will normally execute user code but can be manually forced into ISP operation. This occurs by holding PSEN LOW at the falling edge of reset. If the factory default setting for the boot vector (FCH) is changed, it will no longer point to the factory pre-programmed ISP bootloader code. After programming the flash, the status byte should be programmed to zero in order to allow execution of the user's application code beginning at address 0000H. 6.3.6 ISP ISP is performed without removing the microcontroller from the system. The ISP facility consists of a series of internal hardware resources coupled with internal firmware to facilitate remote programming of the P89CV51RB2/RC2/RD2 through the serial port. This firmware is provided by NXP and embedded within each P89CV51RB2/RC2/RD2 device. The NXP ISP facility has made in-circuit programming in an embedded application possible with a minimum of additional expense in components and circuit board area. The ISP function uses five pins (VDD, VSS, TXD, RXD, and RST). Only a small connector needs to be available to interface your application to an external circuit in order to use this feature. 6.3.7 Using ISP The ISP feature allows for a wide range of baud rates to be used in your application, independent of the oscillator frequency. It is also adaptable to a wide range of oscillator frequencies. This is accomplished by measuring the bit-time of a single bit in a received P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 17 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI character. This information is then used to program the baud rate in terms of timer counts based on the oscillator frequency. The ISP feature requires that an initial character (an uppercase U) be sent to the P89CV51RB2/RC2/RD2 to establish the baud rate. The ISP firmware provides auto-echo of received characters. Once baud rate initialization has been performed, the ISP firmware will only accept Intel Hex-type records. Intel Hex records consist of ASCII characters used to represent hexadecimal values and are summarized below: :NNAAAARRDD..DDCC Table 11. 00 ISP Hex record formats Command/data function Program user code memory :nnaaaa00dd..ddcc Where: nn = number of bytes to program aaaa = address dd..dd = data bytes cc = checksum Example: :09000000010203040506070809CA 01 End of File (EOF), no operation :xxxxxx01cc Where: xxxxxx = required field but value is a don't care cc = checksum Example: :00000001FF 02 not used Record type P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 18 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI ISP Hex record formats ...continued Command/data function Miscellaneous write functions :nnxxxx03ffssddcc Where: nn = number of bytes in the record xxxx = required field but value is a don't care ff = subfunction code ss = selection code dd = data (if needed) cc = checksum Subfunction code = 0C (erase 4 kB blocks) ff = 0C ss = block code, as shown below: block 0, 0 kB to 4 kB, 00H block 1, 4 kB to 8 kB, 10H block 2, 8 kB to 12 kB, 20H block 3, 12 kB to 16 kB, 30H block 4, 16 kB to 20 kB, 40H (only available on P89CV51RC2/RD2) block 5, 20 kB to 24 kB, 50H (only available on P89CV51RC2/RD2) block 6, 24 kB to 28 kB, 60H (only available on P89CV51RC2/RD2) block 7, 28 kB to 32 kB, 70H (only available on P89CV51RC2/RD2) block 8, 32 kB to 36 kB, 80H (only available on P89CV51RD2) block 9, 36 kB to 40 kB, 90H (only available on P89CV51RD2) block 10, 40 kB to 44 kB, A0H (only available on P89CV51RD2) block 11, 44 kB to 48 kB, B0H (only available on P89CV51RD2) block 12, 48 kB to 52 kB, C0H (only available on P89CV51RD2) block 13, 52 kB to 56 kB, D0H (only available on P89CV51RD2) block 14, 56 kB to 60 kB, E0H (only available on P89CV51RD2) block 15, 60 kB to 64 kB, F0H (only available on P89CV51RD2) Example: :020000030C20CF (erase 4 kB block #2) Table 11. 03 Record type P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 19 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI ISP Hex record formats ...continued Command/data function ff = 01 ss = block code, as shown below block 0, 0 kB to 8 kB, 00H block 1, 8 kB to 16 kB, 20H block 2, 16 kB to 32 kB, 40H block 3, 32 kB to 48 kB, 80H block 4, 48 kB to 64 kB, C0H Subfunction code = 04 (erase boot vector and status bit) ff = 04 ss = don't care Subfunction code = 05 (program security bits) ff = 05 ss = 00 program security bit 1 ss = 01 program security bit 2 ss = 02 program security bit 3 Subfunction code = 06 (program status bit, boot vector, 6x/12x bit) ff = 06 dd = data (for boot vector) ss = 00 program status bit ss = 01 program boot vector ss = 02 program 6x/12x bit Subfunction code = 07 (chip erase) Erases code memory and security bits, programs default boot vector and status bit ff = 07 Subfunction code = 08 (erase page, 128 B) ff = 08 ss = high byte of page address (A[15:8]) dd = low byte of page address (A[7:0]) Example: :0300000308E000F2 (erase page at E000H) Table 11. Record type 03 (continued) Subfunction code = 01 (erase blocks) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 20 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI ISP Hex record formats ...continued Command/data function Display device data or blank check :05xxxx04sssseeeeffcc Where 05 = number of bytes in the record xxxx = required field but value is a don't care 04 = function code for display or blank check ssss = starting address, MSB first eeee = ending address, MSB first ff = subfunction 00 = display data 01 = blank check cc = checksum Subfunction codes: Example: :0500000400001FFF00D9 (display from 0000H to 1FFFH) Table 11. 04 Record type 05 Miscellaneous read functions :02xxxx05ffsscc Where: 02 = number of bytes in the record xxxx = required field but value is a don't care 05 = function code for miscellaneous read ffss = subfunction and selection code 0000 = read manufacturer ID 0001 = read device ID 1 0002 = read device ID 2 0003 = read 6x/12x bit (bit 7 = 1 is 6x, bit 7 = 0 is 12x) 0080 = read boot code version 0700 = read security bits 0701 = read status bit 0702 = read boot vector cc = checksum Example: :020000050000F9 (display manufacturer ID) 06 Direct load of baud rate :02xxxx06HHLLcc Where: 02 = number of bytes in the record xxxx = required field but value is a don't care HH = high byte of timer T2 LL = low byte of timer T2 cc = checksum Example: :02000006FFFFcc (load T2 = FFFF) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 21 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.3.8 IAP method Several IAP calls are available for use by an application program to permit selective erasing, reading and programming of flash pages, security bits, status bit, and device ID. All calls are made through a common interface, PGM_MTP. The programming functions are selected by setting up the microcontroller's registers before making a call to PGM_MTP at FFF0H. The IAP calls are shown in Table 12. Table 12. Read ID IAP function calls IAP call parameters Input parameters: R1 = 00H or 80H (WDT feed) DPH = 00H DPL = 00H = manufacturer ID DPL = 01H = device ID 1 DPL = 02H = device ID 2 DPL = 03H = 6x/12x bit (if bit 7 = 1: 6x) DPL = 80H = ISP version number Return parameter(s): ACC = requested parameter Erase 4 kB code block (new function) Input parameters: R0 = oscillator frequency (integer) R1 = 0CH or 8CH (WDT feed) DPH = address of 4 kB code block DPH = 00H, 4 kB block 0, 0 kB to 4 kB DPH = 10H, 4 kB block 1, 4 kB to 8 kB DPH = 20H, 4 kB block 2, 8 kB to 12 kB DPH = 30H, 4 kB block 3, 12 kB to 16 kB DPH = 40H, 4 kB block 4, 16 kB to 20 kB DPH = 50H, 4 kB block 5, 20 kB to 24 kB DPH = 60H, 4 kB block 6, 24 kB to 28 kB DPH = 70H, 4 kB block 7, 28 kB to 32 kB DPH = 80H, 4 kB block 8, 32 kB to 36 kB DPH = 90H, 4 kB block 9, 36 kB to 40 kB DPH = A0H, 4 kB block 10, 40 kB to 44 kB DPH = B0H, 4 kB block 11, 44 kB to 48 kB DPH = C0H, 4 kB block 12, 48 kB to 52 kB DPH = D0H, 4 kB block 13, 52 kB to 56 kB DPH = E0H, 4 kB block 14, 56 kB to 60 kB DPH = F0H, 4 kB block 15, 60 kB to 64 kB DPL = 00H Return parameter(s): ACC = 00: pass ACC is not 00: fail IAP function P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 22 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI IAP function calls ...continued IAP call parameters Input parameters: R1 = 01H or 81H (WDT feed) DPH = 00H, block 0, 0 kB to 8 kB DPH = 20H, block 1, 8 kB to 16 kB DPH = 40H, block 2, 16 kB to 32 kB DPH = 80H, block 3, 32 kB to 48 kB DPH = C0H, block 4, 48 kB to 64 kB Return parameter(s): ACC = 00: pass ACC is not 00: fail Table 12. IAP function Erase 8 kB/16 kB code block Program user code Input parameters: R1 = 02H or 82H (WDT feed) DPH = memory address MSB DPL = memory address LSB ACC = byte to program Return parameter(s): ACC = 00: pass ACC is not 00: fail Read user code Input parameters: R1 = 03H or 83H (WDT feed) DPH = memory address MSB DPL = memory address LSB Return parameter(s): ACC = device data Erase status bit and boot vector Input parameters: R1 = 04H or 84H (WDT feed) DPL = don't care DPH = don't care Return parameter(s): ACC = 00: pass ACC is not 00: fail Program security bits Input parameters: R1 = 05H or 85H (WDT feed) DPL = 00H = security bit 1 DPL = 01H = security bit 2 DPL = 02H = security bit 3 Return parameter(s): ACC = 00: pass ACC is not 00: fail P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 23 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI IAP function calls ...continued IAP call parameters Input parameters: R1 = 06H or 86H (WDT feed) DPL = 00H = program status bit DPL = 01H = program boot vector DPL = 02H = 6x/12x bit ACC = boot vector value to program Return parameter(s): ACC = 00: pass ACC is not 00: fail Table 12. IAP function Program status bit, boot vector, 6x/12x bit Read security bits, status bit, boot vector Input parameters: ACC = 07H or 87H (WDT feed) DPL = 00H = security bits DPL = 01H = status bit DPL = 02H = boot vector Return parameter(s): ACC = 00 SoftICE S/N-match 0 SB 0 DBL_CLK Erase page Input parameters: R1 = 08H or 88H (WDT feed) DPH = page address high byte DPL = page address low byte Return parameter(s): ACC = 00: pass ACC is not 00: fail 6.4 Timers/counters 0 and 1 The two 16-bit timer/counter registers: Timer 0 and Timer 1 can be configured to operate either as timers or event counters (see Table 13 and Table 14). In the `Timer' function, the register is incremented every machine cycle. Thus, one can think of it as counting machine cycles. Since a machine cycle consists of six oscillator periods, the count rate is 16 of the oscillator frequency. In the `Counter' function, the register is incremented in response to a 1-to-0 transition at its corresponding external input pin, T0 or T1. In this function, the external input is sampled once every machine cycle. When the samples show a HIGH in one cycle and a LOW in the next cycle, the count is incremented. The new count value appears in the register in the machine cycle following the one in which the transition was detected. Since it takes two machine cycles (12 oscillator periods) for a 1-to-0 transition to be recognized, the maximum count rate is 1 of the oscillator frequency. There are no restrictions on the duty cycle of the external 12 input signal, but to ensure that a given level is sampled at least once before it changes, it should be held for at least one full machine cycle. In addition to the `Timer' or `Counter' selection, Timer 0 and Timer 1 have four selectable operating modes. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 24 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI The `Timer' or `Counter' function is selected by control bits C/T in the special function register TMOD. These two timers/counters have four operating modes, which are selected by bit-pairs (M1, M0) in TMOD. Modes 0, 1, and 2 are the same for both timers/counters. Mode 3 is different. The four operating modes are described in the following text. Table 13. TMOD - Timer/Counter mode control register (address 89H) bit allocation Not bit addressable; reset value: 0000 0000B; reset source(s): any source. Bit Symbol Table 14. Bit 7 7 T1GATE 6 T1C/T 5 T1M1 4 T1M0 3 T0GATE 2 T0C/T 1 T0M1 0 T0M0 TMOD - Timer/Counter mode control register (address 89H) bit description Symbol T1GATE Description Gating control for Timer 1. When set, timer/counter is enabled only while the INT1 pin is HIGH and the TR1 control bit is set. When cleared, Timer 1 is enabled when the TR1 control bit is set. Timer or counter select for Timer 1. Cleared for timer operation. Set for counter operation (input from T1 input pin). Mode select for Timer 1. Gating control for Timer 0. When set, timer/counter is enabled only while the INT0 pin is HIGH and the TR0 control bit is set. When cleared, Timer 0 is enabled when the TR0 control bit is set. Timer or counter select for Timer 0. Cleared for timer operation. Set for counter operation (input from T0 input pin). Mode select for Timer 0. 6 5 4 3 T1C/T T1M1 T1M0 T0GATE 2 1 0 Table 15. M1 0 0 1 1 T0C/T T0M1 T0M0 TMOD - Timer/Counter mode control register (address 89H) M1/M0 operating mode M0 0 1 0 1 Operating mode 0 1 2 3 8048 timer `TLx' serves as 5-bit prescaler. 16-bit timer/counter `THx' and `TLx' are cascaded; there is no prescaler. 8-bit auto-reload timer/counter `THx' holds a value which is to be reloaded into `TLx' each time it overflows. (Timer 0) TL0 is an 8-bit timer/counter controlled by the standard Timer 0 control bits. TH0 is an 8-bit timer only controlled by Timer 1 control bits. (Timer 1) timer/counter 1 stopped. 1 1 3 Table 16. TCON - Timer/Counter control register (address 88H) bit allocation Bit addressable; reset value: 0000 0000B; reset source(s): any reset. Bit Symbol 7 TF1 6 TR1 5 TF0 4 TR0 3 IE1 2 IT1 1 IE0 0 IT0 P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 25 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI TCON - Timer/Counter control register (address 88H) bit description Symbol TF1 Description Timer 1 overflow Flag. Set by hardware on timer/counter overflow. Cleared by hardware when the processor vectors to Timer 1 interrupt routine, or by software. Timer 1 Run control bit. Set/cleared by software to turn timer/counter 1 on/off. Timer 0 overflow Flag. Set by hardware on timer/counter overflow. Cleared by hardware when the processor vectors to Timer 0 interrupt routine, or by software. Timer 0 Run control bit. Set/cleared by software to turn timer/counter 0 on/off. Interrupt 1 Edge flag. Set by hardware when external interrupt 1 edge/LOW-state is detected. Cleared by hardware when the interrupt is processed, or by software. Interrupt 1 Type control bit. Set/cleared by software to specify falling edge/LOW-state that triggers external interrupt 1. Interrupt 0 Edge flag. Set by hardware when external interrupt 0 edge/LOW-state is detected. Cleared by hardware when the interrupt is processed, or by software. Interrupt 0 Type control bit. Set/cleared by software to specify falling edge/LOW-state that triggers external interrupt 0. Table 17. Bit 7 6 5 TR1 TF0 4 3 TR0 IE1 2 1 IT1 IE0 0 IT0 6.4.1 Mode 0 Putting either timer into Mode 0 makes it look like an 8048 timer, which is an 8-bit counter with a fixed divide-by-32 prescaler. Figure 7 shows Mode 0 operation. overflow osc/6 Tn pin C/T = 0 C/T = 1 TRn TnGate INTn pin 002aaa519 control TLn (5-bits) THn (8-bits) TFn interrupt Fig 7. Timer/counter 0 or 1 in Mode 0 (13-bit counter) In this mode, the timer register is configured as a 13-bit register. As the count rolls over from all 1s to all 0s, it sets the timer interrupt flag TFn. The count input is enabled to the timer when TRn = 1 and either GATE = 0 or INTn = 1. (Setting GATE = 1 allows the timer to be controlled by external input INTn, to facilitate pulse width measurements). TRn is a control bit in the special function register TCON (Table 17). The GATE bit is in the TMOD register. The 13-bit register consists of all 8 bits of THn and the lower 5 bits of TLn. The upper 3 bits of TLn are indeterminate and should be ignored. Setting the run flag (TRn) does not clear the registers. Mode 0 operation is the same for Timer 0 and Timer 1; see Figure 7. There are two different GATE bits, one for Timer 1 (TMOD.7) and one for Timer 0 (TMOD.3). P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 26 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.4.2 Mode 1 Mode 1 is the same as Mode 0, except that all 16 bits of the timer register (THn and TLn) are used; see Figure 8. C/T = 0 osc/6 Tn pin C/T = 1 control TLn (8-bits) THn (8-bits) overflow TFn interrupt TRn TnGate INTn pin 002aaa520 Fig 8. Timer/counter 0 or 1 in Mode 1 (16-bit counter) 6.4.3 Mode 2 Mode 2 configures the timer register as an 8-bit counter (TLn) with automatic reload, as shown in Figure 9. Overflow from TLn not only sets TFn, but also reloads TLn with the contents of THn, which must be preset by software. The reload leaves THn unchanged. Mode 2 operation is the same for Timer 0 and Timer 1. C/T = 0 osc/6 Tn pin C/T = 1 control TLn (8-bits) overflow TFn interrupt reload TRn TnGate INTn pin THn (8-bits) 002aaa521 Fig 9. Timer/counter 0 or 1 in Mode 2 (8-bit auto-reload) 6.4.4 Mode 3 When Timer 1 is in Mode 3 it is stopped (holds its count). The effect is the same as setting TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two separate 8-bit counters. The logic for Mode 3 and Timer 0 is shown in Figure 10. TL0 uses the Timer 0 control bits: T0C/T, T0GATE, TR0, INT0, and TF0. TH0 is locked into a timer function (counting machine cycles) and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0 now controls the Timer 1 interrupt. Mode 3 is provided for applications that require an extra 8-bit timer. With Timer 0 in mode 3, the P89CV51RB2/RC2/RD2 can look like it has an additional timer. Note: When Timer 0 is in Mode 3, Timer 1 can be turned on and off by switching it into and out of its own Mode 3. It can still be used by the serial port as a baud rate generator, or in any application not requiring an interrupt. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 27 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI C/T = 0 osc/6 T0 pin C/T = 1 control TL0 (8-bits) overflow TF0 interrupt TR0 TnGate INT0 pin osc/2 control TH0 (8-bits) overflow TF1 interrupt TR1 002aaa522 Fig 10. Timer/counter 0 Mode 3 (two 8-bit counters) 6.5 Timer 2 Timer 2 is a 16-bit timer/counter which can operate as either an event timer or an event counter, as selected by C/T2 in the special function register T2CON. Timer 2 has four operating modes: Capture, Auto-reload (up or down counting), Clock-out, and Baud rate generator which are selected according to Table 18 using T2CON (Table 19 and Table 20) and T2MOD (Table 21 and Table 22). Table 18. 0 0 0 1 X Timer 2 operating mode CP/RL2 0 1 0 X X TR2 1 1 1 1 0 T2OE 0 0 1 0 X Mode 16-bit auto reload 16-bit capture Programmable clock-out Baud rate generator off RCLK + TCLK Table 19. T2CON - Timer/Counter 2 control register (address C8H) bit allocation Bit addressable; reset value: 00H. Bit Symbol Table 20. Bit 7 7 TF2 6 EXF2 5 RCLK 4 TCLK 3 EXEN2 2 TR2 1 C/T2 0 CP/RL2 T2CON - Timer/Counter 2 control register (address C8H) bit description Symbol TF2 Description Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK or TCLK = 1 or when Timer 2 is in Clock-out mode. Timer 2 external flag is set when Timer 2 is in capture, reload or baud rate mode, EXEN2 = 1 and a negative transition on T2EX occurs. If Timer 2 interrupt is enabled EXF2 = 1 causes the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. Receive clock flag. When set, causes the UART to use Timer 2 overflow pulses for its receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock. 6 EXF2 5 RCLK P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 28 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI T2CON - Timer/Counter 2 control register (address C8H) bit description ...continued Symbol TCLK Description Transmit clock flag. When set, causes the UART to use Timer 2 overflow pulses for its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock. Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX. Start/stop control for Timer 2. A logic 1 enables the timer to run. Timer or counter select. (Timer 2) 0 = internal timer (fosc / 6) 1 = external event counter (falling edge triggered; external clock's maximum rate = fosc / 12) Table 20. Bit 4 3 EXEN2 2 1 TR2 C/T2 0 CP/RL2 Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow. Table 21. T2MOD - Timer 2 mode control register (address C9H) bit allocation Not bit addressable; reset value: XX00 0000B. Bit Symbol Table 22. Bit 7 to 2 1 0 7 6 5 4 3 2 1 T2OE 0 DCEN T2MOD - Timer 2 mode control register (address C9H) bit description Symbol T2OE DCEN Description Reserved for future use. Should be set to 0 by user programs. Timer 2 Output Enable bit. Used in programmable Clock-out mode only. Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter. 6.5.1 Capture mode In the Capture mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2 = 0 Timer 2 is a 16-bit timer or counter (as selected by C/T2 in T2CON) which upon overflowing sets bit TF2, the Timer 2 overflow bit. The Capture mode is illustrated in Figure 11. This bit can be used to generate an interrupt (by enabling the Timer 2 interrupt bit ET2 in the IE register). If EXEN2 = 1, Timer 2 operates as described above, but with the added feature that a 1-to-0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2 like TF2 can generate an interrupt (which vectors to the same location as Timer 2 overflow interrupt). The Timer 2 interrupt service routine can interrogate TF2 and EXF2 to determine which event caused the interrupt. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 29 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI OSC /6 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) TF2 T2 pin C/T2 = 1 TR2 control capture transition detector RCAP2L RCAP2H timer 2 interrupt T2EX pin control EXEN2 EXF2 002aaa523 Fig 11. Timer 2 in Capture mode There is no reload value for TL2 and TH2 in this mode. Even when a capture event occurs from T2EX, the counter keeps on counting T2 pin transitions or fosc / 6 pulses. Since once loaded contents of RCAP2L and RCAP2H registers are not protected, once Timer 2 interrupt is signalled it has to be serviced before a new capture event on T2EX pin occurs. Otherwise, the next falling edge on T2EX pin will initiate reload of the current value from TL2 and TH2 to RCAP2L and RCAP2H and consequently corrupt their content related to the previously reported interrupt. 6.5.2 Auto-reload mode (up or down counter) In the 16-bit auto-reload mode, Timer 2 can be configured as either a timer or counter (via C/T2 in T2CON), then programmed to count up or down. The counting direction is determined by bit DCEN (Down Counter Enable) which is located in the T2MOD register (see Table 21 and Table 22). When reset is applied, DCEN = 0 and Timer 2 will default to counting up. If the DCEN bit is set, Timer 2 can count up or down depending on the value of the T2EX pin. Figure 12 shows Timer 2 counting up automatically (DCEN = 0). OSC /6 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) TF2 T2 pin C/T2 = 1 TR2 control reload transition detector RCAP2L RCAP2H timer 2 interrupt T2EX pin control EXEN2 EXF2 002aaa524 Fig 12. Timer 2 in Auto-reload mode (DCEN = 0) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 30 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI In this mode, there are two options selected by bit EXEN2 in T2CON register. If EXEN2 = 0, then Timer 2 counts up to 0FFFFH and sets the TF2 (overflow flag) bit upon overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in RCAP2L and RCAP2H. The values in RCAP2L and RCAP2H are preset by software means. Auto reload frequency when Timer 2 is counting up can be determined from Equation 1: SupplyFrequency --------------------------------------------------------------------------65536 - ( RCAP2H , RCAP2L ) Where SupplyFrequency is either fosc (C/T2 = 0) or frequency of signal on T2 pin (C/T2 = 1). If EXEN2 = 1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at input T2EX. This transition also sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be generated when either TF2 or EXF2 is 1. The microcontroller's hardware will need three consecutive machine cycles in order to recognize falling edge on T2EX and set EXF2 = 1: in the first machine cycle pin T2EX has to be sampled as 1; in the second machine cycle it has to be sampled as 0, and in the third machine cycle EXF2 will be set to 1. In Figure 13, DCEN = 1 and Timer 2 is enabled to count up or down. This mode allows pin T2EX to control the direction of count. When a logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will overflow at 0FFFFH and set the TF2 flag, which can then generate an interrupt, if the interrupt is enabled. This timer overflow also causes the 16-bit value in RCAP2L and RCAP2H to be reloaded into the timer registers TL2 and TH2. (1) toggle (down-counting reload value) FFH FFH EXF2 OSC /6 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) underflow TF2 overflow timer 2 interrupt T2 pin C/T2 = 1 TR2 control RCAP2L RCAP2H (up-counting reload value) count direction 1 = up 0 = down T2EX pin 002aaa525 Fig 13. Timer 2 in Auto reload mode (DCEN = 1) When a logic 0 is applied at pin T2EX this causes Timer 2 to count down. The timer will underflow when TL2 and TH2 become equal to the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets the TF2 flag and causes 0FFFFH to be reloaded into the timer registers TL2 and TH2. The external flag EXF2 toggles when Timer 2 underflows or overflows. This EXF2 bit can be used as a 17th bit of resolution if needed. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 31 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.5.3 Programmable clock-out A 50 % duty cycle clock can be programmed to come out on pin T2 (P1[0], Clock-out mode). This pin, besides being a regular I/O pin, has two additional functions. It can be programmed: 1. To input the external clock for timer/counter 2, or 2. To output a 50 % duty cycle clock ranging from 122 Hz to 8 MHz at a 16 MHz operating frequency. To configure the timer/counter 2 as a clock generator, bit C/T2 (in T2CON) must be cleared and bit T2OE in T2MOD must be set. Bit TR2 (T2CON.2) also must be set to start the timer. The clock-out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers (RCAP2H, RCAP2L) as shown in Equation 2: OscillatorFrequency -----------------------------------------------------------------------------------------2 x ( 65536 - ( RCAP2H , RCAP2L ) ) Where (RCAP2H, RCAP2L) = the content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer. In the Clock-out mode, Timer 2 roll-overs will not generate an interrupt. This is similar to when it is used as a baud rate generator. (2) 6.5.4 Baud rate generator mode Bits TCLK and/or RCLK in T2CON allow the UART transmit and receive baud rates to be derived from either Timer 1 or Timer 2; see Section 6.6 for details. When TCLK = 0, Timer 1 is used as the UART transmit baud rate generator. When TCLK = 1, Timer 2 is used as the UART transmit baud rate generator. RCLK has the same effect for the UART receive baud rate. With these two bits, the serial port can have different receive and transmit baud rates - Timer 1 or Timer 2. Figure 14 shows Timer 2 in Baud rate generator mode: OSC /2 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) reload TR2 transition detector TX/RX baud rate T2 pin C/T2 = 1 control RCAP2L RCAP2H T2EX pin control EXEN2 EXF2 timer 2 interrupt 002aaa526 Fig 14. Timer 2 in Baud rate generator mode P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 32 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI The Baud rate generator mode is like the Auto-reload mode, when a roll-over in TH2 causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and RCAP2L, which are preset by software. The baud rates in modes 1 and 3 are determined by Timer 2's overflow rate given below: Modes 1 and 3 baud rates = Timer 2 overflow rate / 16 The timer can be configured for either `timer' or `counter' operation. In many applications, it is configured for `timer' operation (C/T2 = 0). Timer operation is different for Timer 2 when it is being used as a baud rate generator. Usually, as a timer it would increment at every machine cycle (i.e., 16 the oscillator frequency). As a baud rate generator, it increments at the oscillator frequency. Thus the baud rate formula is shown in Equation 3: Modes 1 and 3 baud rates = OscillatorFrequency --------------------------------------------------------------------------------------------16 x ( 65536 - ( RCAP2H , RCAP2L ) ) Where: (RCAP2H, RCAP2L) = the content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer. The Timer 2 in Baud rate generator mode is valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a roll-over in TH2 does not set TF2, and will not generate an interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the Baud rate generator mode. Also if the EXEN2 (T2 external enable flag) is set, a 1-to-0 transition in T2EX (timer/counter 2 trigger input) will set EXF2 (T2 external flag) but will not cause a reload from (RCAP2H, RCAP2L) to (TH2, TL2). Therefore when Timer 2 is used as a baud rate generator, T2EX can be used as an additional external interrupt, if needed. When Timer 2 is in the Baud rate generator mode, one should not try to read or write TH2 and TL2. Under these conditions, a read or write of TH2 or TL2 may not be accurate. The RCAP2 registers may be read, but should not be written to, because a write might overlap a reload and cause write and/or reload errors. The timer should be turned off (clear TR2) before accessing the Timer 2 or RCAP2 registers. Table 23 shows commonly used baud rates and how they can be obtained from Timer 2. (3) 6.5.5 Summary of baud rate equations Timer 2 is in Baud rate generator mode: if Timer 2 is being clocked through pin T2 (P1[0]) the baud rate is: Baud rate = Timer 2 overflow rate / 16 If Timer 2 is being clocked internally, the baud rate is: Baud rate = fosc / (16 x (65536 - (RCAP2H, RCAP2L))) Where fosc = oscillator frequency To obtain the reload value for RCAP2H and RCAP2L, this equation can be rewritten as: RCAP2H, RCAP2L = 65536 - fosc / (16 x baud rate) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 33 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Timer 2-generated commonly used baud rates Oscillator frequency 12 MHz 12 MHz 12 MHz 12 MHz 12 MHz 12 MHz 12 MHz 6 MHz 6 MHz Timer 2 RCAP2H RCAP2L FF D9 B2 64 C8 1E AF 8F 57 FF FF FF FF FE FB F2 FD F9 Table 23. Rate 750 kBd 19.2 kBd 9.6 kBd 4.8 kBd 2.4 kBd 600 Bd 220 Bd 600 Bd 220 Bd 6.6 UART The UART operates in all standard modes. Enhancements over the standard 80C51 UART include framing error detection, and automatic address recognition. 6.6.1 Mode 0 Serial data enters and exits through RXD, and TXD outputs the shift clock. Only 8 bits are transmitted or received, LSB first. The baud rate is fixed at 16 of the CPU clock frequency. The UART configured to operate in this mode outputs serial clock on the TXD line no matter whether it sends or receives data on the RXD line. 6.6.2 Mode 1 10 bits are transmitted (through TXD) or received (through RXD): a start bit (logical 0), 8 data bits (LSB first), and a stop bit (logical 1). When data is received, the stop bit is stored in RB8 in special function register SCON. The baud rate is variable and is determined by the Timer 1/Timer 2 overflow rate. 6.6.3 Mode 2 11 bits are transmitted (through TXD) or received (through RXD): start bit (logical 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical 1). When data is transmitted, the 9th data bit (TB8 in special function register SCON) can be assigned the value of 0 or (e.g. the parity bit (P in special function register PSW) could be moved into bit TB8). When data is received, the 9th data bit goes into RB8 in special function register SCON, while the stop bit is ignored. The baud rate is programmable to either 116 or 132 of the CPU clock frequency, as determined by the SMOD1 bit in PCON. 6.6.4 Mode 3 11 bits are transmitted (through TXD) or received (through RXD): a start bit (logical 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical 1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in mode 3 is variable and is determined by the Timer 1/Timer 2 overflow rate. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 34 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 24. SCON - Serial port control register (address 98H) bit allocation Bit addressable; reset value: 00H. Bit Symbol Table 25. Bit 7 7 SM0/FE 6 SM1 5 SM2 4 REN 3 TB8 2 RB8 1 TI 0 RI SCON - Serial port control register (address 98H) bit description Symbol SM0/FE Description The usage of this bit is determined by SMOD0 in the PCON register. If SMOD0 = 0, this bit is SM0, which with SM1, defines the serial port mode. If SMOD0 = 1, this bit is FE (Framing Error). FE is set by the receiver when an invalid stop bit is detected. Once set, this bit cannot be cleared by valid frames but can only be cleared by software. (Note: It is recommended to set up UART mode bits SM0 and SM1 before setting SMOD0 to 1.) With SM0, defines the serial port mode; see Table 26. Enables the multiprocessor communication feature in modes 2 and 3. In Mode 2 or 3, if SM2 is set to 1, then RI will not be activated if the received 9th data bit (RB8) is 0. In Mode 1, if SM2 = 1 then RI will not be activated if a valid stop bit was not received. In Mode 0, SM2 should be 0. Enables serial Reception. Set by software to enable reception. Clear by software to disable reception. The 9th data bit that will be transmitted in modes 2 and 3. Set or clear by software as desired. In modes 2 and 3, is the 9th data bit that was received. In mode 1, if SM2 = 0, RB8 is the stop bit that was received. In Mode 0, RB8 is undefined. Transmit Interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the stop bit in the other modes, in any serial transmission. Must be cleared by software. Receive Interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or approximately halfway through the stop bit time in all other modes. (See SM2 for exceptions). Must be cleared by software. 6 5 SM1 SM2 4 3 2 REN TB8 RB8 1 TI 0 RI Table 26. SM0, SM1 00 01 10 11 SCON - Serial port control register (address 98H) SM0/SM1 mode definition UART mode 0: shift register 1: 8-bit UART 2: 9-bit UART 3: 9-bit UART Baud rate CPU clock / 6 variable CPU clock / 32 or CPU clock / 16 variable 6.6.5 Framing error Framing Error (FE) is reported in the SCON.7 bit if SMOD0 (PCON.6) = 1. If SMOD0 = 0, SCON.7 is the SM0 bit for the UART, it is recommended that SM0 is set up before SMOD0 is set to 1. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 35 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.6.6 More about UART Mode 1 Reception is initiated by a detected 1-to-0 transition at RXD. For this purpose RXD is sampled at a rate of 16 times whatever baud rate has been established. When a transition is detected, the divide-by-16 counter is immediately reset to align its roll-overs with the boundaries of the incoming bit times. The 16 states of the counter divide each bit time into 16ths. At the 7th, 8th, and 9th counter states of each bit time, the bit detector samples the value of RXD. The value accepted is the value that was seen in at least 2 of the 3 samples. This is done for noise rejection. If the value accepted during the first bit time is not 0, the receive circuits are reset and the unit goes back to looking for another 1-to-0 transition. This is to provide rejection of false start bits. If the start bit proves valid, it is shifted into the input shift register, and reception of the rest of the frame will proceed. The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated: (a) RI = 0, and (b) either SM2 = 0, or the received stop bit = 1. If either of these two conditions is not met, the received frame is irretrievably lost. If both conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is activated. 6.6.7 More about UART Modes 2 and 3 Reception is performed in the same manner as in Mode 1. The signal to load special function register SBUF and RB8, and to set RI, will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated: (a) RI = 0, and (b) either SM2 = 0, or the received 9th data bit = 1. If either of these conditions is not met, the received frame is irretrievably lost, and RI is not set. If both conditions are met, the received 9th data bit goes into RB8, and the first 8 data bits go into SBUF. 6.6.8 Multiprocessor communications UART modes 2 and 3 have a special provision for multiprocessor communications. In these modes, 9 data bits are received or transmitted. When data is received, the 9th bit is stored in RB8. The UART can be programmed so that when the stop bit is received, the serial port interrupt will be activated only if RB8 = 1. This feature is enabled by setting bit SM2 in SCON. One way to use this feature in multiprocessor systems is as follows: When the master processor wants to transmit a block of data to one of several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte: the 9th bit is 1 in an address byte and 0 in a data byte. With SM2 = 1, no slave will be interrupted by a data byte, i.e. the received 9th bit is 0. However, an address byte having the 9th bit set to 1 will interrupt all slaves, so that each slave can examine the received byte to see if it is being addressed or not. The addressed slave will clear its SM2 bit and prepare to receive the data (still 9 bits long) that follow. The slaves that were not addressed leave their SM2 bits set and ignore the subsequent data bytes. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 36 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI SM2 has no effect in Mode 0, and in Mode 1 can be used to check the validity of the stop bit, although it is preferable to use the Framing Error flag (FE). When the UART receives data in Mode 1 and SM2 = 1, the receive interrupt will not be activated unless a valid stop bit is received. 6.6.9 Automatic address recognition Automatic address recognition is a feature which allows the UART to recognize certain addresses in the serial bit stream by using hardware to make the comparisons. This feature saves a great deal of software overhead by eliminating the need for the software to examine every serial address which passes by the serial port. This feature is enabled for the UART by setting the SM2 bit in SCON. In the 9-bit UART modes, Mode 2 and Mode 3, the Receive Interrupt flag (RI) will be automatically set when the received byte contains either the `given' address or the `broadcast' address. The 9-bit mode requires that the 9th information bit is a 1 to indicate that the received information is an address and not data. Using the automatic address recognition feature allows a master to selectively communicate with one or more slaves by invoking the given slave address or addresses. All of the slaves may be contacted by using the broadcast address. Two special function registers are used to define the slave's address, SADDR, and the address mask, SADEN. SADEN is used to define which bits in the SADDR are to be used and which bits are don't care. The SADEN mask can be logically ANDed with the SADDR to create the given address which the master will use for addressing each of the slaves. Use of the given address allows multiple slaves to be recognized while excluding others. This device uses the methods presented in Figure 15 to determine if a given or broadcast address has been received or not. rx_byte(7) saddr(7) saden(7) . . . given_address_match rx_byte(0) saddr(0) saden(0) logic used by UART to detect 'given address' in received data saddr(7) saden(7) rx_byte(7) . . . broadcast_address_match saddr(0) saden(0) rx_byte(0) logic used by UART to detect 'given address' in received data 002aaa527 Fig 15. Schemes used by the UART to detect `given' and `broadcast' addresses when multiprocessor communications is enabled The following examples help to show the versatility of this scheme. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 37 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Example 1, slave 0: SADDR = 1100 0000 SADEN = 1111 1101 --------------------------------------------------Given = 1100 00X0 Example 2, slave 1: SADDR = 1100 0000 SADEN = 1111 1110 --------------------------------------------------Given = 1100 000X In the above example SADDR is the same and the SADEN data is used to differentiate between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is ignored. A unique address for slave 0 would be 1100 0010 since slave 1 requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0 (for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000. In a more complex system the following could be used to select slaves 1 and 2 while excluding slave 0. Example 1, slave 0: SADDR = 1100 0000 SADEN = 1111 1001 --------------------------------------------------Given = 1100 0XX0 Example 2, slave 1: SADDR = 1110 0000 SADEN = 1111 1010 --------------------------------------------------Given = 1110 0X0X Example 3, slave 2: SADDR = 1100 0000 SADEN = 1111 1100 --------------------------------------------------Given = 1100 00XX In the above example the differentiation among the 3 slaves is in the lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and it can be uniquely addressed by 1110 0101. Slave 2 requires that bit 2 = 0 and its unique address is 1110 0011. To select slaves 0 and 1 and exclude slave 2 use address 1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2. The broadcast address for each slave is created by taking the logical OR of SADDR and SADEN. Zeros in this result are treated as don't cares. In most cases, interpreting the don't-cares as ones, the broadcast address will be FFH. Upon reset SADDR and SADEN are loaded with 0s. This produces a given address of all don't cares as well as a broadcast address of all don't cares. This effectively disables the automatic addressing mode and allows the microcontroller to use standard UART drivers which do not make use of this feature. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 38 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.7 Serial Peripheral Interface (SPI) 6.7.1 SPI features * * * * * * * Master or slave operation 10 MHz bit frequency (max) LSB first or MSB first data transfer Four programmable bit rates End of transmission (SPIF) Write-collision flag protection (WCOL) Wake-up from Idle mode (Slave mode only) 6.7.2 SPI description The serial peripheral interface allows high-speed synchronous data transfer between the P89CV51RB2/RC2/RD2 and peripheral devices or between several P89CV51RB2/RC2/RD2 devices. Figure 16 shows the correspondence between master and slave SPI devices. The SPICLK pin is the clock output and input for the Master and Slave modes, respectively. The SPI clock generator will start following a write to the master devices SPI data register. The written data is then shifted out of the MOSI pin of the master device into the MOSI pin of the slave device. Following a complete transmission of one byte of data, the SPI clock generator is stopped and the SPI interrupt Flag (SPIF) is set. An SPI interrupt request will be generated if the SPI Interrupt Enable bit (SPIE) and the SPI interrupt enable bit, ES, are both set. An external master drives the Slave Select input pin (SS) LOW to select the SPI module as a slave. If SS has not been driven LOW, then the slave SPI unit is not active and the MOSI pin can also be used as an input port pin. CPHA and CPOL control the phase and polarity of the SPI clock (SCK). Figure 17 and Figure 18 show the four possible combinations of these two bits. MSB master LSB 8-BIT SHIFT REGISTER MISO MISO MSB slave LSB 8-BIT SHIFT REGISTER MOSI MOSI SPI CLOCK GENERATOR SCK SS VDD SCK SS VSS 002aaa528 Fig 16. SPI master-slave interconnection P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 39 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 27. SPCR - SPI control register (address D5H) bit allocation Reset source(s): any reset; reset value: 0000 0000B. Bit Symbol Table 28. Bit 7 6 5 4 3 2 1 7 SPIE 6 SPEN 5 DORD 4 MSTR 3 CPOL 2 CPHA 1 SPR1 0 SPR0 SPCR - SPI control register (address D5H) bit description Description SPI interrupt enable. If both SPIE = 1 and ES = 1, SPI interrupts are enabled. SPI enable bit. When set enables SPI. Data transmission order. 0 = MSB first; 1 = LSB first in data transmission. Master/Slave select. 1 = Master mode, 0 = Slave mode. Clock polarity. 1 = SPICLK is HIGH when idle (active LOW), 0 = SPICLK is LOW when idle (active HIGH). Clock Phase control bit. 1 = shift-triggered on the trailing edge of the clock; 0 = shift-triggered on the leading edge of the clock. SPI clock Rate select bit 1. Along with SPR0 controls the SPICLK rate of the device when a master. SPR1 and SPR0 have no effect on the slave; see Table 29. SPI clock Rate select bit 0. Along with SPR1 controls the SPICLK rate of the device when a master. SPR1 and SPR0 have no effect on the slave; see Table 29. Symbol SPIE SPEN DORD MSTR CPOL CPHA SPR1 0 SPR0 Table 29. SPR1 0 0 1 1 SPCR - SPI control register (address D5H) clock rate selection SPR0 0 1 0 1 SPICLK = fosc divided by 6-clock mode 2 8 32 64 12-clock mode 4 16 64 128 Table 30. SPSR - SPI Status Register (address AAH) bit allocation Reset source(s): any reset; reset value: 0000 0000B. Bit Symbol Table 31. Bit 7 7 SPIF 6 WCOL 5 4 3 2 1 0 - SPSR - SPI Status Register (address AAH) bit description Symbol SPIF Description SPI interrupt flag. Upon completion of data transfer, this bit is set to 1. If SPIE = 1 and ES = 1, an interrupt is then generated. This bit is cleared by software. Write Collision flag. Set if the SPI data register is written to during data transfer. This bit is cleared by software. Reserved for future use. Should be set to 0 by user programs. 6 5 to 0 WCOL - P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 40 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI SCK cycle # (for reference) SCK (CPOL = 0) SCK (CPOL = 1) MOSI (from master) MISO (from slave) SS (to slave) 1 2 3 4 5 6 7 8 MSB MSB 6 6 5 5 4 4 3 3 2 2 1 1 LSB LSB 002aaa529 Fig 17. SPI transfer format with CPHA = 0 SCK cycle # (for reference) SCK (CPOL = 0) SCK (CPOL = 1) MOSI (from master) MISO (from slave) SS (to slave) 1 2 3 4 5 6 7 8 MSB MSB 6 6 5 5 4 4 3 3 2 2 1 1 LSB LSB 002aaa530 Fig 18. SPI transfer format with CPHA = 1 6.8 Watchdog timer The WDT is intended as a recovery method in situations where the CPU may be subjected to software upset. The WDT consists of a 14-bit counter and the WatchDog Timer Reset (WDTRST) SFR. The WDT is disabled at reset. To enable the WDT, the user must write 01EH and 0E1H, in sequence, to the WDTRST SFR. When the WDT is enabled, it will increment every machine cycle while the oscillator is running. There is no way to disable the WDT, except through a reset (either a hardware reset or a WDT overflow reset). When the WDT overflows, it will drive an output reset HIGH pulse at the RST pin. When the WDT is enabled (and thus running) the user needs to reset it by writing 01EH and 0E1H, in sequence, to the WDTRST SFR to avoid WDT overflow. The 14-bit counter reaches overflow when it reaches 16383 (3FFFH) and this will reset the device. The WDT's counter cannot be read or written. When the WDT overflows it will generate an output pulse at the RST pin with a duration of 98 oscillator periods in 6-clock mode or 196 oscillator periods in 12-clock mode. 6.9 PCA The PCA includes a special 16-bit timer that has five 16-bit capture/compare modules associated with it. Each of the modules can be programmed to operate in one of four modes: rising and/or falling edge capture, software timer, high-speed output, or pulse-width modulator. Each module has a pin associated with it: Module 0 is connected P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 41 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI to CEX0, module 1 to CEX1, etc. Registers CH and CL contain the current value of the free-running up-counting 16-bit PCA timer. The PCA timer is a common time base for all five modules and can be programmed to run at: 16 the oscillator frequency, 12 the oscillator frequency, the Timer 0 overflow, or the input on the ECI pin (P1[2]). The timer count source is determined from the CPS1 and CPS0 bits in the CMOD SFR; see Table 32 and Table 33. 16 bits MODULE0 P1[3]/CEX0 MODULE1 16 bits P1[4]/CEX1 PCA TIMER/COUNTER time base for PCA modules Module functions: - 16-bit capture - 16-bit timer - 16-bit high speed output - 8-bit PWM - watchdog timer (module 4 only) MODULE2 P1[5]/CEX2 MODULE3 P3[4]/T0/CEX3 MODULE4 P3[5]/T1/CEX4 002aab913 Fig 19. PCA In the CMOD SFR there are three additional bits associated with the PCA. They are CIDL which allows the PCA to stop during Idle mode, WDTE which enables or disables the watchdog function on module 4, and ECF which when set causes an interrupt and the PCA overflow flag CF (in the CCON SFR) to be set when the PCA timer overflows. The watchdog timer function is implemented in module 4 of PCA. The CCON SFR contains the run control bit for the PCA (CR) and the flags for the PCA timer (CF) and each module (CCF[4:0]). To run the PCA the CR bit (CCON.6) must be set by software. The PCA is shut off by clearing this bit. The CF bit (CCON.7) is set when the PCA counter overflows and an interrupt will be generated if the ECF bit in the CMOD register is set. The CF bit can only be cleared by software. Bits 0 through 4 of the CCON register are the flags for the modules (bit 0 for module 0, bit 1 for module 1, etc.) and are set by hardware when either a match or a capture occurs. These flags can only be cleared by software. All the modules share one interrupt vector. The PCA interrupt system is shown in Figure 20. Each module in the PCA has a special function register associated with it. These registers are: CCAPM0 for module 0, CCAPM1 for module 1, etc. The registers contain the bits that control the mode that each module will operate in. The ECCF bit (from CCAPMn.0 where n = 0, 1, 2, 3, or 4 depending on the module) enables the CCFn flag in the CCON SFR to generate an interrupt when a match or compare occurs in the associated module; see Figure 20. PWM (CCAPMn.1) enables the Pulse-width modulation mode. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 42 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI The TOG bit (CCAPMn.2) when set causes the CEX output associated with the module to toggle when there is a match between the PCA counter and the module's capture/compare register. The match bit MAT (CCAPMn.3) when set will cause the CCFn bit in the CCON register to be set when there is a match between the PCA counter and the module's capture/compare register. The next two bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5) determine the edge that a capture input will be active on. The CAPN bit enables the negative edge, and the CAPP bit enables the positive edge. If both bits are set both edges will be enabled and a capture will occur for either transition. The last bit in the register ECOM (CCAPMn.6) when set enables the comparator function. There are two additional registers associated with each of the PCA modules. They are CCAPnH and CCAPnL and these are the registers that store the 16-bit count when a capture occurs or a compare should occur. When a module is used in the PWM mode, these registers are used to control the duty cycle of the output. CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 CCON (D8H) PCA TIMER/COUNTER MODULE0 IE.6 EC IE.7 EA to interrupt priority decoder MODULE1 MODULE2 MODULE3 MODULE4 CMOD.0 ECF CCAPMn.0 ECCFn 002aaa533 Fig 20. PCA interrupt system Table 32. CMOD - PCA counter mode register (address C1H) bit allocation Not bit addressable; reset value: 00H. Bit Symbol 7 CIDL 6 WDTE 5 4 3 2 CPS1 1 CPS0 0 ECF P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 43 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI CMOD - PCA counter mode register (address C1H) bit description Symbol CIDL Description Counter Idle control. CIDL = 0 programs the PCA counter to continue functioning during Idle mode; CIDL = 1 programs it to be gated off during Idle mode. WatchDog Timer Enable. WDTE = 0 disables watchdog timer function on module 4; WDTE = 1 enables it. Reserved for future use. Should be set to 0 by user programs. PCA Count Pulse Select; see Table 34. PCA Enable Counter overflow interrupt Flag. ECF = 1 enables CF bit in CCON to generate an interrupt; ECF = 0 disables that function. Table 33. Bit 7 6 5 to 3 2 to 1 0 WDTE CPS1, CPS0 ECF Table 34. CPS1 0 0 1 1 CMOD - PCA counter mode register (address C1H) count pulse select CPS0 0 1 0 1 Select PCA input 0 internal clock, fosc / 6 1 internal clock, fosc / 6 2 Timer 0 overflow 3 external clock at pin P1[2]/ECI (maximum rate = fosc / 4) Table 35. CCON - PCA counter control register (address D8H) bit allocation Bit addressable; reset value: 00H. Bit Symbol Table 36. Bit 7 7 CF 6 CR 5 4 CCF4 3 CCF3 2 CCF2 1 CCF1 0 CCF0 CCON - PCA counter control register (address D8H) bit description Symbol CF Description PCA Counter overflow Flag. Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is set. CF may be set by either hardware or software but can only be cleared by software. PCA Counter Run control. Set by software to turn the PCA counter on. Must be cleared by software to turn the PCA counter off. Reserved for future use. Should be set to 0 by user programs. PCA Module 4 interrupt Flag. Set by hardware when a match or capture occurs. Must be cleared by software. PCA Module 3 interrupt Flag. Set by hardware when a match or capture occurs. Must be cleared by software. PCA Module 2 interrupt Flag. Set by hardware when a match or capture occurs. Must be cleared by software. PCA Module 1 interrupt Flag. Set by hardware when a match or capture occurs. Must be cleared by software. PCA Module 0 interrupt Flag. Set by hardware when a match or capture occurs. Must be cleared by software. 6 5 4 3 2 1 0 CR CCF4 CCF3 CCF2 CCF1 CCF0 P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 44 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 37. CCAPMn - PCA modules compare/capture register (address CCAPM0 DAH, CCAPM1 DBH, CCAPM2 DCH, CCAPM3 DDH, CCAPM4 DEH) bit allocation Not bit addressable; reset value: 00H. Bit Symbol Table 38. Bit 7 6 5 4 3 7 6 ECOMn 5 CAPPn 4 CAPNn 3 MATn 2 TOGn 1 PWMn 0 ECCFn CCAPMn - PCA modules compare/capture register (address CCAPM0 DAH, CCAPM1 DBH, CCAPM2 DCH, CCAPM3 DDH, CCAPM4 DEH) bit description Symbol ECOMn CAPPn CAPNn MATn Description Reserved for future use. Should be set to 0 by user programs. Enable Comparator. ECOMn = 1 enables the comparator function. Capture Positive, CAPPn = 1 enables positive edge capture. Capture Negative, CAPNn = 1 enables negative edge capture. Match. When MATn = 1 a match of the PCA counter with this module's compare/capture register causes the CCFn bit in CCON to be set, flagging an interrupt. Toggle. When TOGn = 1, a match of the PCA counter with this module's compare/capture register causes the CEXn pin to toggle. Pulse Width Modulation mode. PWMn = 1 enables the CEXn pin to be used as a pulse-width modulated output. Enable CCF interrupt. Enables compare/capture flag CCFn in the CCON register to generate an interrupt. 2 1 0 TOGn PWMn ECCFn Table 39. ECOMn 0 X X X 1 1 1 1 PCA module modes (CCAPMn register) CAPPn 0 1 0 1 0 0 0 0 CAPNn 0 0 1 1 0 0 0 0 MATn 0 0 0 0 1 1 0 1 TOGn 0 0 0 0 0 1 0 X PWMn 0 0 0 0 0 0 1 0 ECCFn 0 X X X X X 0 X Module function no operation 16-bit capture by a positive-edge trigger on CEXn 16-bit capture by a negative-edge trigger on CEXn 16-bit capture by any transition on CEXn 16-bit software timer 16-bit high-speed output 8-bit PWM watchdog timer 6.9.1 PCA capture mode To use one of the PCA modules in the Capture mode (Figure 21), either one or both of the CCAPM bits CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1) is sampled for a transition. When a valid transition occurs, the PCA hardware loads the value of the PCA counter registers (CH and CL) into the module's capture registers (CCAPnL and CCAPnH). P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 45 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 CCON (D8H) PCA interrupt (to CCFn) PCA timer/counter CH CL capture CEXn CCAPnH CCAPnL - ECOMn 0 CAPPn CAPNn MATn 0 TOGn 0 PWMn 0 ECCFn CCAPMn, n = 0 to 4 (DAH to DEH) 002aaa538 Fig 21. PCA Capture mode If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated. 6.9.2 16-bit software timer mode The PCA modules can be used as software timers (Figure 22) by setting both the ECOM and MAT bits in the modules CCAPMn register. The PCA timer will be compared to the module's capture registers and when a match occurs an interrupt will occur if the CCFn (CCON SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 46 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI CF write to CCAPnH write to CCAPnL CR - CCF4 CCF3 CCF2 CCF1 CCF0 CCON (D8H) reset CCAPnH CCAPnL match 16-BIT COMPARATOR (to CCFn) PCA interrupt 0 1 enable CH CL PCA timer/counter - ECOMn CAPPn 0 CAPNn 0 MATn 1 TOGn 0 PWMn 0 ECCFn CCAPMn, n = 0 to 4 (DAH to DEH) 002aaa539 Fig 22. PCA Compare mode 6.9.3 High-speed output mode In this mode (Figure 23) the CEX output (on port 1) associated with the PCA module will toggle each time a match occurs between the PCA counter and the module's capture registers. To activate this mode the TOG, MAT, and ECOM bits in the module's CCAPMn SFR must be set. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 47 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI CF write to CCAPnH write to CCAPnL CR - CCF4 CCF3 CCF2 CCF1 CCF0 CCON (D8H) reset CCAPnH CCAPnL match 16-BIT COMPARATOR (to CCFn) PCA interrupt 0 1 enable CH CL PCA timer/counter toggle CEXn - ECOMn CAPPn 0 CAPNn 0 MATn 1 TOGn 0 PWMn 0 ECCFn CCAPMn, n = 0 to 4 (DAH to DEH) 002aaa540 Fig 23. PCA High-speed output mode 6.9.4 Pulse width modulator mode All of the PCA modules can be used as PWM outputs (Figure 24). Output frequency depends on the source for the PCA timer. CCAPnH CCAPnL enable 8-BIT COMPARATOR 0 CL < CCAPnL CEXn CL CCAPnL CL PCA timer/counter 1 - ECOMn 1 CAPPn 0 CAPNn 0 MATn 0 TOGn 0 PWMn 1 ECCFn 1 CCAPMn, n = 0 to 4 (DAH to DEH) 002aaa541 Fig 24. PCA PWM mode All of the modules will have the same output frequency because they all share only one PCA timer. The duty cycle of each module is independently variable using the module's capture register CCAPnL. When the value of the PCA CL SFR is less than the value in the P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 48 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI module's CCAPnL SFR, the output will be LOW; when it is equal to, or greater, the output will be HIGH. When CL overflows from FFH to 00H, CCAPnL is reloaded with the value in CCAPnH. This allows the PWM to be updated without glitches. The PWM and ECOM bits in the module's CCAPMn register must be set to enable PWM mode. 6.9.5 PCA watchdog timer An on-board watchdog timer is available with the PCA to improve the reliability of the system without increasing chip count. Watchdog timers are useful for systems that are susceptible to noise, power glitches, or electrostatic discharge. Module 4 is the only PCA module that can be programmed as a watchdog. However, this module can still be used for other modes if the watchdog is not needed. Figure 24 shows a diagram of how the watchdog works. The user pre-loads a 16-bit value in the compare registers. Just like the other compare modes, this 16-bit value is compared to the PCA timer value. If a match is allowed to occur, an internal reset will be generated. This will not cause the RST pin to be driven HIGH. User's software then must periodically change (CCAP4H, CCAP4L) to keep a match from occurring with the PCA timer (CH, CL). This code is given in the subroutine WATCHDOG shown below. In order to hold off the reset, the user has three options: * Periodically change the compare value so it will never match the PCA timer. * Periodically change the PCA timer value so it will never match the compare values. * Disable the watchdog by clearing the WDTE bit before a match occurs and then re-enable it. The first two options are more reliable because the watchdog timer is never disabled as in the third option. If the program counter ever reaches an undesired value, a match will eventually occur and cause an internal reset. The second option is also not recommended if other PCA modules are being used. Remember that the PCA timer is the time base for all modules; changing the time base for other modules is not recommended. Thus, in most applications the first option is best. ;CALL the following WATCHDOG subroutine periodically. CLR EA ;Hold off interrupts MOV CCAP4L,#00 ;Next compare value is within 255 counts of current PCA timer value MOV CCAP4H,CH SETB EA ;Re-enable interrupts RET Do not use this routine as part of an interrupt service routine, because if the program counter would enter an infinite loop, still interrupts will be serviced and the watchdog will continually keep getting reset. Because this would defeat the purpose of the watchdog, it is recommended that this subroutine is called from the main program within 216 PCA timer counts. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 49 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.10 Security bits The security bits protect against software piracy and prevent the contents of the flash from being read by unauthorized parties in Parallel programmer mode and ISP mode. Since the end application might need to erase pages and read from the code memory, the security bits have no effect in IAP mode. However, the security bits' programmed/erased state may be read using IAP function calls allowing the end-user code to limit access, if desired. The security bits and their effects are shown in Table 40. Note: On this device, MOVC instructions executed from external code memory are prevented from fetching code bytes from internal code memory. Table 40. 1 2 3 Security bit functions Description Write protect. When programmed, prohibits further erasing or programming, except to program other security bits or a chip erase. Read protect. When programmed, inhibits reading of user code memory. External execution inhibit. When programmed, prevents any execution of instructions from external code memory. Security bit 6.11 Interrupt priority and polling sequence The device supports eight interrupt sources under a four-level priority scheme. Table 41 summarizes the polling sequence of the supported interrupts. Note that the SPI serial interface and the UART share the same interrupt vector; see Figure 25. Table 41. Interrupt polling sequence Interrupt flag IE0 TF0 IE1 TF1 TI/RI SPIF CF/CCFn TF2, EXF2 Vector address Interrupt enable 0003H 000BH 0013H 001BH 0023H 0023H 0033H 003BH EX0 ET0 EX1 ET1 ES ES EC ET2 Interrupt priority PX0/PX0H PT0/PT0H PX1/PX1H PT1/PT1H PS/PSH PS/PSH PPC/PPCH PT2/PT2H Service priority 1 (highest) 2 3 4 5 5 7 6 Wake-up Power-down yes no yes no no no no no Description External Interrupt 0 T0 External Interrupt 1 T1 UART SPI PCA T2 P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 50 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI IE and IEA registers 0 INT0# 1 IT0 IE0 IP/IPH/IPA/IPAH registers highest priority interrupt TF0 interrupt polling sequence 0 INT1# 1 IT1 IE1 TF1 ECF CF CCFn ECCFn RI TI SPIF SPIE TF2 EXF2 lowest priority interrupt 002aac965 individual enables global disable Fig 25. Interrupt structure Table 42. IE - Interrupt enable register 0 (address A8H) bit allocation Bit addressable; reset value: 00H. Bit Symbol Table 43. Bit 7 6 5 7 EA 6 EC 5 ET2 4 ES 3 ET1 2 EX1 1 ET0 0 EX0 IE - Interrupt enable register 0 (address A8H) bit description Symbol EA EC ET2 Description Interrupt Enable. EA = 1: interrupt(s) can be serviced; EA = 0: interrupt servicing disabled. PCA interrupt Enable. Timer 2 interrupt Enable. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 51 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI IE - Interrupt enable register 0 (address A8H) bit description ...continued Symbol ES ET1 EX1 ET0 EX0 Description Serial port interrupt Enable. Timer 1 overflow interrupt Enable. External interrupt 1 Enable. Timer 0 overflow interrupt Enable. External interrupt 0 Enable. Table 43. Bit 4 3 2 1 0 Table 44. IP - Interrupt priority low register (address B8H) bit allocation Bit addressable; reset value: 00H. Bit Symbol Table 45. Bit 7 6 5 4 3 2 1 0 7 6 PPC 5 PT2 4 PS 3 PT1 2 PX1 1 PT0 0 PX0 IP - Interrupt priority low register (address B8H) bit description Symbol PPC PT2 PS PT1 PX1 PT0 PX0 Description Reserved for future use. Should be set to 0 by user programs. PCA interrupt Priority Low. Timer 2 interrupt Priority Low. Serial Port interrupt Priority Low. Timer 1 interrupt Priority Low. External interrupt 1 Priority Low. Timer 0 interrupt Priority Low. External interrupt 0 Priority Low. Table 46. IPH - Interrupt priority high register (address B7H) bit allocation Not bit addressable; reset value: 00H. Bit Symbol Table 47. Bit 7 6 5 4 3 2 1 0 7 6 PPCH 5 PT2H 4 PSH 3 PT1H 2 PX1H 1 PT0H 0 PX0H IPH - Interrupt priority high register (address B7H) bit description Symbol PPCH PT2H PSH PT1H PX1H PT0H PX0H Description Reserved for future use. Should be set to 0 by user programs. PCA interrupt Priority High. Timer 2 interrupt Priority High. Serial Port interrupt Priority High. Timer 1 interrupt Priority High. External interrupt 1 Priority High. Timer 0 interrupt Priority High. External interrupt 0 Priority High. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 52 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.12 Power-saving modes The device provides two power-saving modes of operation for applications where power consumption is critical. The two modes are Idle and Power-down; see Table 48. 6.12.1 Idle mode Idle mode is entered by setting the IDL bit in the PCON register. In Idle mode, the program counter is stopped. The system clock continues to run and all interrupts and peripherals remain active. The on-chip RAM and the special function registers hold their data during this mode. The device exits Idle mode through either a system interrupt or a hardware reset. When exiting Idle mode via system interrupt, the start of the interrupt clears the IDL bit and exits Idle mode. After exiting the Interrupt Service Routine (ISR), the interrupted program resumes execution at the instruction immediately following the instruction which invoked the Idle mode. A hardware reset starts the device similar to a power-on reset. 6.12.2 Power-down mode The Power-down mode is entered by setting the PD bit in the PCON register. In the Power-down mode, the clock is stopped and external interrupts are active for level-sensitive interrupts only. SRAM contents are retained during power-down, the minimum VDD level is 4.5 V. The device exits Power-down mode through either an enabled external level-sensitive interrupt or a hardware reset. The start of the interrupt clears the PD bit and exits power-down. Holding an external interrupt pin LOW restarts the oscillator, the signal must hold LOW at least 1024 clock cycles before bringing back HIGH to complete the exit. When the interrupt signal is restored to logic VIH, the interrupt service routine program execution resumes at the instruction immediately following the instruction which invoked Power-down mode. A hardware reset starts the device similar to a power-on reset. To exit properly out of power-down, the reset or external interrupt should not be executed before the VDD line is restored to its normal operating voltage. Be sure to hold VDD voltage long enough at its normal operating level for the oscillator to restart and stabilize (normally less than 10 ms). Table 48. Mode Idle Power-saving modes Initiated by Software (Set IDL bit in PCON) MOV PCON, #01H State of MCU CLK is running. Interrupts, serial port and timers/counters are active. Program counter is stopped. ALE and PSEN signals at a HIGH-state during Idle. All registers remain unchanged. CLK is stopped. On-chip SRAM and SFR data is maintained. ALE and PSEN signals at a LOW-state during power-down. External interrupts are only active for level-sensitive interrupts, if enabled. Exited by Enabled interrupt or hardware reset. Start of interrupt clears IDL bit and exits Idle mode, after the ISR RETI instruction, program resumes execution beginning at the instruction following the one that invoked Idle mode. A hardware reset restarts the device similar to a power-on reset. Enabled external level-sensitive interrupt or hardware reset. Start of interrupt clears PD bit and exits Power-down mode, after the ISR RETI instruction program resumes execution beginning at the instruction following the one that invoked Power-down mode. A hardware reset restarts the device similar to a power-on reset. Power-down Software (Set PD bit in PCON) MOV PCON, #02H P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 53 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.13 System clock and clock options 6.13.1 Clock input options and recommended capacitor values for oscillator Shown in Figure 26 and Figure 27 are the input and output of an internal inverting amplifier (XTAL1, XTAL2), which can be configured for use as an on-chip oscillator. When driving the device from an external clock source, XTAL2 should be left disconnected and XTAL1 should be driven. At start-up, the external oscillator may encounter a higher capacitive load at XTAL1 due to interaction between the amplifier and its feedback capacitance. However, the capacitance will not exceed 15 pF once the external signal meets the VIL and VIH specifications. Resonator manufacturer, supply voltage, and other factors may cause circuit performance to differ from one application to another. C1 and C2 should be adjusted appropriately for each design. Table 49 shows the typical values for C1 and C2 versus resonator type for various frequencies. Table 49. Resonator Quartz Ceramic Recommended values for C1 and C2 by crystal type C1 = C 2 20 pF to 30 pF 40 pF to 50 pF C2 XTAL2 XTAL1 C1 VSS 002aaa545 Fig 26. Oscillator characteristics (using the on-chip oscillator) n.c. XTAL2 external oscillator signal XTAL1 VSS 002aaa546 Fig 27. Oscillator characteristics (external clock drive) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 54 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 6.13.1.1 Clock control register (CKCON) By default, the device runs at twelve clock cycles per machine cycle (12-clock mode). The device may be run at 6 clock cycles per machine cycle (6-clock mode) by programming of either a non-volatile bit (FX2) or an SFR bit (X2); see Table 52 "Clock modes". If the FX2 non-volatile bit is programmed, the device will run in 6-clock mode and the X2 SFR bit has no effect. If the FX2 bit is erased, then the clock mode is controlled by the X2 SFR bit. Table 50. CKCON - Clock control register (address 8FH) bit allocation Not bit addressable; reset value 00H. Bit Symbol Table 51. Bit 7 6 5 4 3 2 1 0 7 SPIX2 6 WDX2 5 PCAX2 4 SIX2 3 T2X2 2 T1X2 1 T0X2 0 X2 CKCON - Clock control register (address 8FH) bit description Symbol SPIX2 WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 X2 Description SPI clock; 0 = 6 clock cycles for each SPI clock cycle; 1 = 12 clock cycles Watchdog clock; 0 = 6 clock cycles for each WDT clock cycle; 1 = 12 clock cycles PCA clock; 0 = 6 clock cycles for each PCA clock cycle; 1 = 12 clock cycles UART clock; 0 = 6 clock cycles for each UART clock cycle; 1 = 12 clock cycles Timer 2 clock; 0 = 6 clock cycles for each Timer 2 clock cycle; 1 = 12 clock cycles Timer 1 clock; 0 = 6 clock cycles for each Timer 1 clock cycle; 1 = 12 clock cycles Timer 0 clock; 0 = 6 clock cycles for each Timer 0 clock cycle; 1 = 12 clock cycles CPU clock; 0 = 12 clock cycles for each machine cycle; 1 = 6 clock cycles Table 52. Clock modes CPU clock mode 12-clock (default) 6-clock 6-clock Peripheral clock mode bit (e.g. T0X2) X 0 1 0 1 Mode 12-clock (default) 6-clock 12-clock 6-clock 12-clock FX2 clock mode bit X2 bit erased 0 1 programmed X P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 55 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 7. Limiting values Table 53. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Parameters are valid over operating temperature range unless otherwise specified; all voltages are with respect to VSS unless otherwise noted. Symbol Tamb(bias) Tstg VI Vn IOL(I/O) Ptot(pack) Parameter bias ambient temperature storage temperature input voltage voltage on any other pin LOW-level output current per input/output pin total power dissipation (per package) based on package heat transfer, not device power consumption on EA pin to VSS except VSS; with respect to VDD Conditions Min -55 -65 -0.5 -0.5 Max +125 +150 +14 VDD + 0.5 15 1.5 Unit C C V V mA W 8. Static characteristics Table 54. Static characteristics Tamb = -40 C to +85 C; VDD = 4.5 V to 5.5 V; VSS = 0 V. Symbol nendu(fl) tret(fl) Ilatch Vth(HL) Vth(LH) VOL Parameter endurance of flash memory I/O latch-up current HIGH-LOW threshold voltage LOW-HIGH threshold voltage LOW-level output voltage except XTAL1, RST VDD = 4.5 V; except PSEN, ALE IOL = 1.6 mA VDD = 4.5 V; ALE, PSEN IOL = 3.2 mA VOH HIGH-level output voltage VDD = 4.5 V; ports 1, 2, 3, 4 IOH = -30 A VDD = 4.5 V; port 0 in External bus mode, ALE, PSEN IOH = -3.2 mA IIL ITHL ILI LOW-level input current HIGH-LOW transition current input leakage current VI = 0.4 V; ports 1, 2, 3, 4 VI = 2 V; ports 1, 2, 3, 4 0.45 V < VI < VDD - 0.3 V; port 0 0 V < VI < 6 V P89CV51RB2_RC2_RD2_1 Conditions JEDEC Standard A117 JEDEC Standard 78 [1] [1] [1] Min 10000 100 100 + IDD -0.5 Typ - Max +0.2VDD - 0.1 VDD + 0.5 Unit cycles years mA V V flash memory retention time JEDEC Standard A103 0.2VDD + 0.9 [2][3][4] [5] - 0.4 0.45 V V VDD - 0.7 - - V VDD - 0.7 -1 [6] - -75 -650 10 10 V A A A A (c) NXP B.V. 2007. All rights reserved. - Product data sheet Rev. 01 -- 5 October 2007 56 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 54. Static characteristics ...continued Tamb = -40 C to +85 C; VDD = 4.5 V to 5.5 V; VSS = 0 V. Symbol Rpd Ciss IDD(oper) Parameter pull-down resistance input capacitance operating supply current Conditions on pin RST 1 MHz; Tamb = 25 C; VI = 0 V fosc = 12 MHz fosc = 40 MHz Programming and erase mode IDD(idle) IDD(pd) Idle mode supply current Power-down mode supply current fosc = 12 MHz fosc = 40 MHz minimum VDD = 4.5 V [7] Min 40 - Typ - Max 225 15 11.5 50 70 8.5 42 90 Unit k pF mA mA mA mA mA A [1] [2] This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. Under steady state (non-transient) conditions, IOL must be externally limited as follows: a) Maximum IOL per 8-bit port: 26 mA b) Maximum IOL total for all outputs: 71 mA c) If IOL exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. Capacitive loading on Ports 0 and 2 may cause spurious noise to be superimposed on the VOL of ALE and Ports 1 and 3. The noise is due to external bus capacitance discharging into the Port 0 and 2 pins when the pins make 1-to-0 transitions during bus operations. In the worst cases (capacitive loading > 100 pF), the noise pulse on the ALE pin may exceed 0.8 V. In such cases, it may be desirable to qualify ALE with a Schmitt trigger, or use an address latch with a Schmitt trigger STROBE input. Load capacitance for Port 0, ALE and PSEN = 100 pF, load capacitance for all other outputs = 80 pF. Capacitive loading on Ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the VDD - 0.7 V specification when the address bits are stabilizing. Pins of Ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its maximum value when VI is approximately 2 V. Pin capacitance is characterized but not tested. Capacitance on pin EA = 25 pF (max.). [3] [4] [5] [6] [7] P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 57 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 50 IDD (mA) 40 002aaa813 (1) (2) 30 20 (3) 10 (4) 0 0 10 20 30 40 internal clock frequency (MHz) (1) Maximum active IDD (2) Maximum idle IDD (3) Typical active IDD (4) Typical idle IDD Fig 28. IDD as a function of frequency P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 58 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 9. Dynamic characteristics Table 55. Dynamic characteristics Over operating conditions: load capacitance for port 0, ALE, and PSEN = 100 pF; load capacitance for all other outputs = 80 pF. Tamb = -40 C to +85 C; VDD = 4.5 V to 5.5 V; VSS = 0 V.[1][2] Symbol Parameter fosc oscillator frequency Conditions 12-clock mode 6-clock mode IAP tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ tPXAV tAVIV tPLAZ tRLRH tWLWH tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tWHQX tQVWH tRLAZ tWHLH [1] [2] Min 0 0 0.25 2Tcy(clk) - 15 Tcy(clk) - 15 Tcy(clk) - 15 Tcy(clk) - 15 3Tcy(clk) - 15 0 Tcy(clk) - 8 6Tcy(clk) - 30 6Tcy(clk) - 30 0 3Tcy(clk) - 15 4Tcy(clk) - 30 Tcy(clk) - 20 7Tcy(clk) - 50 Tcy(clk) - 15 Typ - Max 40 20 40 4Tcy(clk) - 45 3Tcy(clk) - 50 Tcy(clk) - 15 5Tcy(clk) - 60 10 5Tcy(clk) - 50 2Tcy(clk) - 12 8Tcy(clk) - 50 9Tcy(clk) - 75 3Tcy(clk) + 15 0 Tcy(clk) + 15 Unit MHz MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ALE pulse width address valid to ALE LOW time address hold after ALE LOW time ALE LOW to valid instruction in time ALE LOW to PSEN LOW time PSEN pulse width PSEN LOW to valid instruction in time input instruction hold after PSEN time input instruction float after PSEN time PSEN to address valid time address to valid instruction in time PSEN LOW to address float time RD LOW pulse width WR LOW pulse width RD LOW to valid data in time data hold after RD time data float after RD time ALE LOW to valid data in time address to valid data in time ALE LOW to RD or WR LOW time address to RD or WR LOW time data hold after WR time data output valid to WR HIGH time RD LOW to address float time RD or WR HIGH to ALE HIGH time Tcy(clk) = 1 / fosc. Calculated values are for 6-clock mode only. P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 59 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 9.1 Explanation of symbols Each timing symbol used in Figure 29 to Figure 33 has 5 characters. The first character is always a `t' (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. A -- Address C -- Clock D -- Input data H -- Logic level HIGH I -- Instruction (program memory contents) L -- Logic level LOW or ALE P -- PSEN Q -- Output data R -- RD signal T -- cycle Time V -- Valid W -- WR signal X -- No longer a valid logic level Z -- High impedance (float) Example: tAVLL = Address valid to ALE LOW time tLLPL = ALE LOW to PSEN LOW time tLHLL ALE tAVLL tLLPL PSEN tPLAZ tLLAX port 0 A0 to A7 tAVIV port 2 A8 to A15 A8 to A15 002aaa548 tPLPH tLLIV tPLIV tPXAV tPXIZ tPXIX INSTR IN A0 to A7 Fig 29. External program memory read cycle P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 60 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI ALE tWHLH PSEN tLLDV tLLWL tRLRH RD tAVLL tLLAX tRLAZ tRLDV tRHDX tRHDZ port 0 A0 to A7 from RI to DPL tAVWL tAVDV DATA IN A0 to A7 from PCL INSTR IN port 2 P2.0 to P2.7 or A8 to A15 from DPH A0 to A15 from PCH 002aaa549 Fig 30. External data memory read cycle tLHLL ALE tWHLH PSEN tLLWL tWLWH WR tAVLL tLLAX tWHQX tQVWH port 0 A0 to A7 from RI or DPL tAVWL DATA OUT A0 to A7 from PCL INSTR IN port 2 P2[7:0] or A8 to A15 from DPH A8 to A15 from PCH 002aaa550 Fig 31. External data memory write cycle P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 61 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI Table 56. Symbol External clock drive Parameter Oscillator 40 MHz Min Max 10 10 Variable Min 0 0.35Tcy(clk) 0.35Tcy(clk) Max 40 0.65Tcy(clk) 0.65Tcy(clk) MHz ns ns ns ns ns Unit fosc Tcy(clk) tCHCX tCLCX tCLCH tCHCL oscillator frequency clock cycle time clock HIGH time clock LOW time clock rise time clock fall time 25 8.75 8.75 - VDD - 0.5 V 0.45 V 0.2VDD + 0.9 V 0.2VDD - 0.1 V tCHCL tCLCX Tcy(clk) 002aaa907 tCHCX tCLCH Fig 32. External clock drive waveform Table 57. Symbol Serial port timing Parameter Oscillator 40 MHz Min TXLXL tQVXH tXHQX tXHDX tXHDV serial port clock cycle time output data set-up to clock rising edge time output data hold after clock rising edge time 0.3 117 0 Max 117 Variable Min 12Tcy(clk) Max s ns ns ns Unit 10Tcy(clk) - 133 2Tcy(clk) - 50 0 - input data hold after clock rising edge 0 time input data valid to clock rising edge time - 10Tcy(clk) - 133 ns P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 62 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI instruction ALE 0 1 2 3 4 5 6 7 8 tXLXL clock tQVXH output data 0 write to SBUF input data clear RI set RI 002aaa552 tXHQX 1 tXHDX 2 3 4 5 6 7 tXHDV valid valid valid valid valid valid valid set TI valid Fig 33. Shift register mode timing waveforms Table 58. Symbol fSPI TSPICYC tSPILEAD tSPILAG tSPICLKH tSPICLKL tSPIDSU tSPIDH tSPIA tSPIDIS tSPIDV tSPIOH tSPIR SPI interface timing Parameter SPI operating frequency SPI cycle time SPI enable lead time SPI enable lag time SPICLK HIGH time SPICLK LOW time SPI data set-up time SPI data hold time SPI access time SPI disable time SPI enable to output data valid time SPI output data hold time SPI rise time see Figure 34, 35, 36, 37 see Figure 36, 37 see Figure 36, 37 see Figure 34, 35, 36, 37 see Figure 34, 35, 36, 37 master or slave; see Figure 34, 35, 36, 37 master or slave; see Figure 34, 35, 36, 37 see Figure 36, 37 see Figure 36, 37 see Figure 34, 35, 36, 37 see Figure 34, 35, 36, 37 see Figure 34, 35, 36, 37 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) tSPIF SPI fall time see Figure 34, 35, 36, 37 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) 100 2000 100 2000 ns ns 100 2000 100 2000 ns ns Conditions Variable clock Min 0 4Tcy(clk) 250 250 2Tcy(clk) 2Tcy(clk) 100 100 0 0 0 Max Tcy(clk) / 4 80 160 111 fosc = 18 MHz Min 0 222 250 250 111 111 100 100 0 0 Max 10 80 160 111 MHz ns ns ns ns ns ns ns ns ns ns ns Unit P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 63 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI SS TSPICYC tSPIF tSPICLKH SPICLK (CPOL = 0) (output) tSPIF tSPICLKL tSPIR tSPICLKH SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIDH LSB/MSB in tSPIOH tSPIDV tSPIR tSPICLKL tSPIR MSB/LSB in tSPIDV MOSI (output) tSPIF master MSB/LSB out master LSB/MSB out 002aaa908 Fig 34. SPI master timing (CPHA = 0) SS TSPICYC tSPIF tSPICLKL tSPIR tSPICLKH SPICLK (CPOL = 0) (output) tSPIF SPICLK (CPOL = 1) (output) tSPICLKH tSPICLKL tSPIR tSPIDSU MISO (input) tSPIDH LSB/MSB in tSPIOH tSPIDV tSPIDV tSPIR MSB/LSB in tSPIDV MOSI (output) tSPIF master MSB/LSB out master LSB/MSB out 002aaa909 Fig 35. SPI master timing (CPHA = 1) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 64 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI SS tSPIR tSPILEAD SPICLK (CPOL = 0) (input) tSPIF SPICLK (CPOL = 1) (input) tSPIA tSPIOH tSPIDV MISO (output) tSPIF TSPICYC tSPICLKH tSPICLKL tSPIR tSPILAG tSPIR tSPICLKL tSPIR tSPICLKH tSPIOH tSPIDV tSPIOH tSPIDIS slave MSB/LSB out slave LSB/MSB out not defined tSPIDSU MOSI (input) tSPIDH tSPIDSU tSPIDSU tSPIDH MSB/LSB in LSB/MSB in 002aaa910 Fig 36. SPI slave timing (CPHA = 0) SS tSPIR tSPILEAD SPICLK (CPOL = 0) (input) tSPIF SPICLK (CPOL = 1) (input) tSPIOH tSPIDV tSPIA MISO (output) not defined slave MSB/LSB out slave LSB/MSB out tSPICLKL tSPIR tSPICLKH tSPIF tSPICLKH tSPIR tSPIR tSPILAG TSPICYC tSPICLKL tSPIOH tSPIDV tSPIOH tSPIDV tSPIDIS tSPIDSU MOSI (input) tSPIDH tSPIDSU tSPIDSU tSPIDH MSB/LSB in LSB/MSB in 002aaa911 Fig 37. SPI slave timing (CPHA = 1) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 65 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI to tester to DUT CL 002aaa555 Fig 38. Test load example VDD P0 VDD RST EA VDD IDD 8 VDD DUT clock signal (n.c.) XTAL2 XTAL1 VSS 002aaa556 All other pins disconnected Fig 39. IDD test condition, Active mode VDD P0 RST EA VDD IDD 8 VDD DUT clock signal (n.c.) XTAL2 XTAL1 VSS 002aaa557 All other pins disconnected Fig 40. IDD test condition, Idle mode P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 66 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI VDD = 4.5 V VDD P0 RST EA VDD IDD 8 VDD DUT (n.c.) XTAL2 XTAL1 VSS 002aad019 All other pins disconnected Fig 41. IDD test condition, Power-down mode P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 67 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 10. Package outline TQFP44: plastic thin quad flat package; 44 leads; body 10 x 10 x 1.0 mm SOT376-1 c y X A 33 34 23 22 ZE e E HE wM pin 1 index bp A A2 A1 (A 3) Lp L 44 1 11 ZD bp D HD wM 12 detail X e vM A B vM B 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.2 A1 0.15 0.05 A2 1.05 0.95 A3 0.25 bp 0.45 0.30 c 0.18 0.12 D (1) 10.1 9.9 E (1) 10.1 9.9 e 0.8 HD HE L 1 Lp 0.75 0.45 v 0.2 w 0.2 y 0.1 Z D(1) Z E(1) 1.2 0.8 1.2 0.8 7o o 0 12.15 12.15 11.85 11.85 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT376-1 REFERENCES IEC 137E08 JEDEC MS-026 JEITA EUROPEAN PROJECTION ISSUE DATE 00-01-19 02-03-14 Fig 42. Package outline SOT376-1 (TQFP44) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 68 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI PLCC44: plastic leaded chip carrier; 44 leads SOT187-2 eD y X A ZE eE 39 29 28 bp 40 b1 wM 44 HE A e A4 A1 (A 3) k 7 e D HD 17 ZD B vMB vM A 6 18 Lp detail X 1 pin 1 index E 0 5 scale 10 mm DIMENSIONS (mm dimensions are derived from the original inch dimensions) A4 A1 e UNIT A A3 D(1) E(1) eD eE HD bp b1 max. min. mm inches 4.57 4.19 0.51 0.25 0.01 3.05 0.12 0.53 0.33 0.81 0.66 HE k Lp 1.44 1.02 v 0.18 w 0.18 y 0.1 ZD(1) ZE(1) max. max. 2.16 2.16 16.66 16.66 16.00 16.00 17.65 17.65 1.22 1.27 16.51 16.51 14.99 14.99 17.40 17.40 1.07 0.63 0.59 0.63 0.59 45 o 0.180 0.02 0.165 0.021 0.032 0.656 0.656 0.05 0.013 0.026 0.650 0.650 0.695 0.695 0.048 0.057 0.007 0.007 0.004 0.085 0.085 0.685 0.685 0.042 0.040 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT187-2 REFERENCES IEC 112E10 JEDEC MS-018 JEITA EDR-7319 EUROPEAN PROJECTION ISSUE DATE 99-12-27 01-11-14 Fig 43. Package outline SOT187-2 (PLCC44) P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 69 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 11. Abbreviations Table 59. Acronym ALE CPU DPTR DUT EPROM EMI ID IAP ISP LSB MCU MSB PCA PCH PCL PWM RAM RC SFR SPI SRAM UART WDT Abbreviations Description Address Latch Enable Central Processing Unit Data PoinTeR Device Under Test Erasable Programmable Read-Only Memory Electro-Magnetic Interference IDentifier In-Application Programming In-System Programming Least Significant Bit MicroController Unit Most Significant Bit Programmable Counter Array Programmable Counter High Programmable Counter Low Pulse-Width Modulator Random Access Memory Resistance-Capacitance Special Function Register Serial Peripheral Interface Static Random Access Memory Universal Asynchronous Receiver/Transmitter WatchDog Timer P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 70 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 12. Revision history Table 60. Revision history Release date Data sheet status Product data sheet Change notice Supersedes Document ID P89CV51RB2_RC2_RD2_1 20071005 P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 71 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 13. Legal information 13.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 13.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 13.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or 13.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 14. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com P89CV51RB2_RC2_RD2_1 (c) NXP B.V. 2007. All rights reserved. Product data sheet Rev. 01 -- 5 October 2007 72 of 73 NXP Semiconductors P89CV51RB2/RC2/RD2 80C51 with 1 kB RAM, SPI 15. Contents 1 2 2.1 2.2 2.3 3 3.1 4 5 5.1 5.2 6 6.1 6.2 6.2.1 6.2.2 6.2.3 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.3.8 6.4 6.4.1 6.4.2 6.4.3 6.4.4 6.5 6.5.1 6.5.2 6.5.3 6.5.4 6.5.5 6.6 6.6.1 6.6.2 6.6.3 6.6.4 6.6.5 6.6.6 6.6.7 6.6.8 6.6.9 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Principal features . . . . . . . . . . . . . . . . . . . . . . . 1 Additional features . . . . . . . . . . . . . . . . . . . . . . 1 Comparison to P89C51RB2/RC2/RD2 devices 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 8 Special function registers . . . . . . . . . . . . . . . . . 8 Memory organization . . . . . . . . . . . . . . . . . . . 12 Expanded data RAM addressing . . . . . . . . . . 12 Dual data pointers. . . . . . . . . . . . . . . . . . . . . . 14 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Flash memory. . . . . . . . . . . . . . . . . . . . . . . . . 16 Flash organization . . . . . . . . . . . . . . . . . . . . . 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Boot block . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power-on reset code execution. . . . . . . . . . . . 17 Hardware activation of the bootloader . . . . . . 17 ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Using ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 IAP method . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Timers/counters 0 and 1 . . . . . . . . . . . . . . . . . 24 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Timer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Capture mode . . . . . . . . . . . . . . . . . . . . . . . . . 29 Auto-reload mode (up or down counter) . . . . . 30 Programmable clock-out . . . . . . . . . . . . . . . . . 32 Baud rate generator mode . . . . . . . . . . . . . . . 32 Summary of baud rate equations . . . . . . . . . . 33 UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Framing error . . . . . . . . . . . . . . . . . . . . . . . . . 35 More about UART Mode 1 . . . . . . . . . . . . . . . 36 More about UART Modes 2 and 3 . . . . . . . . . 36 Multiprocessor communications . . . . . . . . . . . 36 Automatic address recognition . . . . . . . . . . . . 37 Serial Peripheral Interface (SPI). . . . . . . . . . . SPI features . . . . . . . . . . . . . . . . . . . . . . . . . . SPI description . . . . . . . . . . . . . . . . . . . . . . . . Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . PCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCA capture mode. . . . . . . . . . . . . . . . . . . . . 16-bit software timer mode. . . . . . . . . . . . . . . High-speed output mode . . . . . . . . . . . . . . . . Pulse width modulator mode . . . . . . . . . . . . . PCA watchdog timer . . . . . . . . . . . . . . . . . . . Security bits . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt priority and polling sequence . . . . . . Power-saving modes . . . . . . . . . . . . . . . . . . . Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-down mode . . . . . . . . . . . . . . . . . . . . . System clock and clock options . . . . . . . . . . . Clock input options and recommended capacitor values for oscillator . . . . . . . . . . . . . 6.13.1.1 Clock control register (CKCON) . . . . . . . . . . . 7 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 8 Static characteristics . . . . . . . . . . . . . . . . . . . 9 Dynamic characteristics . . . . . . . . . . . . . . . . . 9.1 Explanation of symbols . . . . . . . . . . . . . . . . . 10 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . 13 Legal information . . . . . . . . . . . . . . . . . . . . . . 13.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 13.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Contact information . . . . . . . . . . . . . . . . . . . . 15 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 6.7.1 6.7.2 6.8 6.9 6.9.1 6.9.2 6.9.3 6.9.4 6.9.5 6.10 6.11 6.12 6.12.1 6.12.2 6.13 6.13.1 39 39 39 41 41 45 46 47 48 49 50 50 53 53 53 54 54 55 56 56 59 60 68 70 71 72 72 72 72 72 72 73 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 5 October 2007 Document identifier: P89CV51RB2_RC2_RD2_1 |
Price & Availability of P89CV51RD2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |